joint seam的例句大全

on the bottom of the bottle there is no joint seam, and the strength is improved.

瓶底无接合线并且强度增加。

Finite Element Analysis of Stress Field in Anamorphic Joint Seam

结构变形缝部位应力场的有限元分析

the joint seam on the bottle body is smooth.

瓶身的接合线平滑。

sealing for visible part of car body and generic joint seam, for example skirt plate, vehicle bottom.

可用于各种车辆的车体可视部分及一般接缝密封，如裙板、行李仓盖板、车底等。

Development of Automatic Arc Welding Machine for Saddle Joint Seam on Large-diameter Cylinders

大直径筒体马鞍形曲线自动焊接机的研制

the arrangement of joint seam in vessel head plate

封头拼缝位置的布置及探讨

The major research results are summarized as follows: ( 1) On the joint seam face of combining power house with the dam, the transferring force appears to be in parabola distribution in height direction.

厂坝联合接缝面，传力在高度方向呈抛物线分布，缝顶和缝底传力较小，中部最大。

Study showed that angle deformation of T joint is changed along the welded seam length.

研究表明,T形接头的角变形沿焊缝长度方向是变化的.

The machine is mainly used for extrusion and connection of 45 ° seam casement window with angle joint structure.

门窗单头组角机主要用于角码结构的平开门窗45°接缝的挤压联结。

The brazing-ability and quality of brazed seam of 6063 aluminum alloy brazed by Al-Si eutectic filler metal and QF flux is discussed by means of test of spread-ability and test of T joint.

本文用平百铺展试验和T型接头试验，研究了6063铝合金采用AI－St钎料和氟化物钎剂（QF钎剂）钎焊时的钎焊性和钎缝质量。

The simulation mentioned above was confirmed by series experiments, and the proper thickness of the brazed seam is 50~ 80 μ m for the CRB joint of Al with Si as an interlayer.

在试验证明FEM计算结果的可靠性的基础上，给出了Si为中间层进行LF21铝合金接触反应钎焊时，其合适的钎缝宽度范围是50～80μm。

The results suggest the joint is not ideal if the Cu layer is too thin or too thick, and it is very important for existing some eutectic substance in brazed seam.

研究表明，Cu层的厚度太薄或者太厚，其连接效果都很不理想，同时在Al合金与Cu中间层接触反应钎焊中，钎缝区存在适当的液相对于提高接头强度是至关重要的。

The effect on the microstructures of the brazing seam of Ag-CdO contact terminal and Cu contact bridge by different brazing technological parameters including temperature, holding time and joint gap was analyzed. Based on the analysis, the optimum technological criteria put forward.

分析了Ag-CdO触头与Cu触桥钎焊温度、保温时间、钎焊间隙对钎缝组织的影响，并提出了获得理想组织的最佳工艺规范。

A moving utensil for portable ultrasonic probe which is made of chargeable electronic screwdriver is introduced, and it can be used to assist detector to detect steel butt-joint welding seam.

介绍一种利用充电电动螺丝批改制的轻便手持式超声波探头移动器，可辅助检测人员进行钢板对接焊缝的超声波检测工作，从而提高检测工作效率、减轻工作强度。

Butt-jointed Seam Saddle Welding for Clad Plate of Low Content Alloy and Heat-Resistant Steel& Major Diameter Thick-walled Tube

低合金耐热钢复合板与大直径厚壁接管马鞍形对接焊

The joint structure and element distribution at brazing seam are also studied by SEM/ EDAX and thermodynamics measures.

通过SEM/EDAX以及热力学方法分析了钎焊接头组织及钎缝的成分分布。

They can hide in the seam of your mattress or a joint in your bed frame.

他们会藏在床垫缝里或者你床架的连接处。

in co2 gas metal arc welding, the difficulty hi seam tracking by pendular arc sensor is how to attain the tolerance signal of weld joint.

在CO_2气体保护焊中，采用摆动电弧传感器进行焊缝跟踪的困难在于如何提取准确的焊缝偏差信号。

in pressure vessels, c and d seam which are located at the joint of flange, tube-shape object, jointed tube, and head of pressure vessels separately are the most complex seams.

压力容器设备中法兰与筒体、法兰与接管连接处的C类焊缝和封头端部、筒体上马鞍形的D类焊缝是最为不规则的且施焊工艺最为复杂的焊缝。

Add shirring to back joint waist seam . Ensure shirring matches shirring along front waist seam.

后腰线加碎褶, 确保碎褶与前腰线相配.