length bar的例句大全

A convenient system is designed to calculate the tooth profile error. This system includes the calculation of the inner gear length bar size, the common normal line, the chordal thickness and so on.

设计出便于工人进行齿形误差计算的交互式系统，主要涵盖量柱距、公法线和弦齿厚等常用检测项。

The optimization of tension Hopkinson bar ( TSHB) tests has been studied. The structure and loading conditions of TSHB have evident influence on test results including the gauge length and geometry of specimen, interconnecting linkage, contact boundary, stress waves and so on.

研究了拉伸Hopkinson试验（TSHB）的优化问题：Hopkinson拉伸试验装置的结构及加载条件明显影响试验结果，其中包括试件的几何形状、试件与杆的连接以及接触边界、应力波的影响。

In this paper the quality problems of cold-drawn thick reinforced bar are analyzed. A new method is proposed, which can not only ensure the plasticity and strength but also meet the demand of tension length.

提出了既能保证钢筋冷拉后有一定塑性和强度储备，又能满足张拉后钢筋长度要求的新方法，达到了冷拉钢筋质量合格的效果。

Parameters calculation of roller bed and brake plate between double length shear and cooling bed of bar continuous rolling line

棒材连轧倍尺剪后辊道及制动板参数的确定

In proportion as the mouth of the cove was wider compared with its length, the water over the bar was deeper compared with that in the basin.

正如凹处的口上，阔度大于它的长度，沙洲上的水，在同比例度内，比盆地的水更深。

The easiest way is to change the configuration of ground-based equipment, such as moving beam bar to change the ground and the pump stroke length;

最简单的做法是改变地面设备的配置，如移动游梁拉杆来改变地面和泵的冲程长度；

When in use, the rapping bar can be undrawn to a required length according to different height demands so as to easily flap mosquitoes and flies.

本实用新型在使用时可根据不同高度需求，将拍杆拉开所需长度，这样就很方便地拍打蚊子、苍蝇。

This provides the method to calculate the anchor strengthening action area coefficient K_l and design the length of an anchor bar considering the minimum depth of the bearing bar permitted by the stability of the base rocks, K_l and the dis-tance between anchor bars.

给出了锚杆加固影响范围系数K l的计算方法，并根据围岩稳定所必须形成的承压拱最小厚度、锚杆加固影响范围系数K l和锚杆的间距来确定锚杆长度的方法。

The primary factors for influencing working space are analysed. The restriction conditions are deduced, such as parallel bar length, motion fit corner, parallel bar interference and framework restriction.

分析了影响工作空间的主要因素，推导出并联杆长度、运动副转角、并联杆干涉和结构限制等的约束条件。

The research indicates the bond stress decreases with the increase of the diameter and the embedded length of a steel bar.

结果表明：粘结应力受钢筋埋长、钢筋直径等因素的影响，随着埋长与钢筋直径的增大而减小。

This article will present the rational optimization of the hoisted point on a whole stand bar tower of single point hoisting, the length of the pole, and the angle of inclination to find its optimum association.

采用单纯形法优选抱杆参数，对单点吊整立杆塔的吊点位置、抱杆的长度、倾角和固定钢绳绳角进行合理的优化，从而找到了最优组合。

Experiment and Research on the Bar Anchorage Length in Grouted Cells of Reinforced Block Masonry

配筋砌块砌体芯柱中钢筋锚固的试验研究

Test parameters include temperature, anchorage length, FRP bar diameter, strength grades of concrete, thickness of concrete cover and fire-retardant coating.

试验参数包括温度、粘结长度、FRP筋直径、混凝土强度等级、混凝土保护层厚度及混凝土表面涂刷防火涂料。

To Contrapose the construction length of the reinforcing steel bar in calculation is very complicated, criterion is disperse, the application is discommodious, text advances a simplification calculation methods and gives the interrelated sheet.

针对钢筋下料长度计算复杂，规范分散，应用不便的问题，本文提出了一种简化计算方法，并整理出相应的表格。

A double dotted half note or minim is equal in length to three quarter notes or crotchets and an 8th note or quaver. a time signature indicating four beats to the bar.

半音加两个符点，时值等于三个四分音符或一个八分音符。每小节有四个四分音符或与其相当的音乐时值。

In this paper, the author analyses the error in the horizontal four bar linkage so that length error in each bar is set, transmission accuracy is increased and cost is minimized

通过对平面四连杆机构的误差分析，确定各杆的长度公差，提高传动精度，降低制造成本

Length insufficience of reinforced bar tooth and settlement method

螺纹钢牙筋长度不足的原因及解决办法

The cause of influence on reinforced bar tooth length has been analyzed.

分析了影响螺纹钢牙筋长度的原因。

With the change in temperature, the length of the iron bar has changed.

随着温度的变化，铁棒的长度起了变化。

This paper expounds a new method on confirming the location and magnitude of minimum transmission angle, which is based on the relationship of component length in designed plane cower four-bar linkage.

阐述了在设计好的平面低副四杆机构中，由杆长关系确定最小传动角位置及大小的新方法。