length feed的例句大全

Tangential motion along grinding wheel face is achieved by the length feed of the lathe working table, and normal motion jiggle inputting along grinding wheel face is achieved by the minute displacement mechanism of the dressing tool.

其中沿砂轮表面切向运动由机床工作台的纵向进给运动完成，而沿砂轮表面法向运动的微进给运动由修整器的微位移机构来实现。

Calculating and measuring the full bin capacity, time of each bin, mixing delay capacity, feed time difference, and mixing length, etc., are investigated in this paper.

本文计算并测定了FA022型多仓混棉机的各仓一次充满容量和一次充满时间、混和时延容量、时间差及混和长度等；

It is possible to use simple delimiting strategies such as separation by Linefeed ( LF), End of Line ( EOL), Carriage Return, Line Feed ( CRLF), Fixed Length, Whole-file or User-defined.

可以使用简单的分隔策略，如按换行（LF）、行尾（EOL）、回车换行（CRLF）、固定长度、整个文件或用户定义的方式进行分隔。

The regressive equation between rape feed, cylinder line speed, cylinder length, and threshing and separating rate is established based on the test results using DPS and is simulated.

运用DPS数据处理系统对试验结果进行处理，建立了油菜喂入量、脱粒滚筒线速度、脱粒滚筒长度与脱粒分离率的回归方程，并进行了计算机仿真。

The plant consists of a burner, a reactor with a diameter of 0.3 m and a length of 4.5 m, a whirlwind separator, a feed system and a return system.

该实验装置由燃烧器、高45m直径030m的反应器、旋风分离器、给料系统和物料回送系统等组成。

The influences of the inlet diameter, overflow diameter, underflow extension pipe length, split ratio, feed flowrate and temperature on the separation performance are analyzed.

探讨了溢流分率、溢流口直径、进料浓度、入口直径、尾管长度、进料流量及温度等对旋流器分离性能的影响。

It introduced imitating surfaces with bicubic parametric curves, feed length, cutter location and vector of cutter location.

介绍用双三次参数曲线拟合曲面、平头铣刀的直径、铣削的步长及行距选择、刀位点和刀轴矢量的计算。

In this embodiment, the feed conductor 106 is part of the antenna length.

在该实施例中, 馈送导体106是天线长度的一部分.

It introduced imitating surfaces with bicubic parametric curves, feed length, cutter location and vector of location.

介绍用双三次参数曲线拟合曲面、平头铣刀的直径 、 铣削的步长及行距选择 、 刀位点和刀轴矢量的计算.

Feed the animals by hanging a of raw meat on a length of thread.

把生肉吊在一根绳子上给那些动物吃.

Based on the designed thin film evaporator, the influence of the rotor speed, feed rate and liquid inlet temperature on evaporation length and film heat transfer coefficient was primarily discussed using the software CFX 4.4 with water as feed liquid.

针对自行设计的薄膜蒸发器，以水为物料，采用大型CFD软件CFX4.4，初步探讨了刮板转速、进料量、进料温度等参量对薄膜蒸发器蒸发段长度和加热段膜内传热系数的影响。

The free through-feed grinding method is adopted to grind the OD of small sized non-symmetric spherical rollers on centerless CD grinder with common corundum guide wheels, i. e. grinding slopes with same angle but different length on both sides first, then going on through-feed grinding.

采用自由贯穿磨削方法，在无心外圆磨床上用普通砂质导轮磨削小型非对称球面滚子外径，即先在圆柱滚子两端磨出角度相同但长度不同的斜度，然后进行贯穿磨削。