line slip的例句大全

He let the line slip through his fingers while he reached down with his left hand and made fast the free end of the two reserve coils to the loop of the two reserve coils of the next line.

他让钓索在指间朝下溜，同时伸出左手，把两卷备用钓索的一端紧系在旁边那根钓索的两卷备用钓索上。

Multi-Wheels Fitting Control of a Lunar Rover with On-Line Slip Ratio Estimation

基于滑转率在线估计的月面巡视探测器多轮协调控制

It was the weight of the fish and he let the line slip down, down, down, unrolling off the first of the two reserve coils.

这是鱼本身的重量造成的，他就松手让钓索朝下溜，一直朝下，朝下溜，从那两卷备用钓索中的一卷上放出钓索。

The results show that the four failure modes were ranked from highest to lowest effect: slip along the foundation, non-uniform distributions of stress, tension crack of the floodgate heel in the upper stream and compression failure of the floodgate toe in the downstream line.

由计算结果看出，水闸闸室沿闸基面滑动为水闸的最主要失效模式，上下游应力不均匀、上游闸踵拉裂、下游闸趾压坏为次要失效模式。

Determination of slip surface in slope based on theory of slip line field

基于滑移线场理论的边坡滑裂面确定方法

Model of assessing shallow planar landslide of forested soil side slope Fold line plane was more suitable than the circular slip plane for the shallow slide.

造林土质边坡浅层平面滑坡模型的初步研究对于膨胀土边坡的浅层滑动面，采用折线滑动面比圆弧滑动面更接近于实际情况。

Long range and short range frictional slip-lines on plane contact surface in plastic compression ( the rule of isoclinic gradient)

塑压接触平面上之长程滑动与短程滑动（等倾陡线规律）

As the alternating stress and the continuing role of the corrosion, cracks along the two are not mutually parallel to the ( 111) slip plane expansion, crack propagation direction parallel to ( 111) planes of the cross-lines, namely, ( 110) direction.

随着交变应力和腐蚀的继续作用，裂纹沿着两组互不平行的{111}滑移面扩展，裂纹的扩展方向平行于{111}面的交线，即{110}方向。

Based on the theory of slip line and plastic deformation of metal, the clamping force for forging reduction of cylinder is analyzed and studied.

应用滑移线理论和金属的塑性变形理论，分析研究圆柱体镦粗过程中的夹紧力的计算方法，并与试验结果进行比较。

In consideration on the on-line R-value measurement of aluminum deep drawing sheets, the selection of initial slip systems was analyzed according to the activation process of the slip systems during plastic deformation. Initial R values of the 3104 aluminum sheet in different directions were calculated.

以深冲铝板R值的在线检测为应用背景，塑性变形滑移系开动的过程为出发点，分析了初始滑移系选取的方式，并计算了不同取向3104铝合金板的初始R值。

A new method for building the sector slip line field& arc method

一种建立有心扇形滑移线场的新方法&圆弧法

The slip line based Mold Element with the Mold Element principle and method is the key research work.

本文以已提出的模型元分析法为理论依据，研究其基本原理和应用；

The basic principle and its application was made on the basis of existing Mold Element Method; The slip line based Mold Element with the Mold Element principle and method is the key research work.

本文属于模型元方法在体积成形领域的应用研究。本文以已提出的模型元分析法为理论依据，研究其基本原理和应用；

Design of the novel three-phase and four-line digital slip energy recovering system

新型三相四线制串级数字调速系统设计

The graphical method for the construction of complex slip line field

利用图解方法求解复杂滑移线场

By studying the effects of the structural parameters of reinforcement and face plate, some qualitative rule is proposed, for example, the anchor should be 1.5 times length than distance between slip crack line and dam slope, and so on.

通过对加筋层支护结构及护面板的参数的变化研究，建议加筋长取滑裂面至边坡的1.5-2倍等一些定性的规律。

Research on combinatorial solution of slip line and upper bound methods

滑移线与上界法组合的解法研究

A Graphic Analysis for Stress in the Slip Line Fields

滑移线场应力图解法

ImproVement of The Method for Determining The Direction of Plastic Slip Line

确定塑性平面应变滑移场方向的一个简便方法

A graphic analysis for stress in slip line field by use of linear mapping

利用线性映射图解滑移线场应力