liquid layer的例句大全

The research indicates that the temperature tremble and the temperature distribution as well as the temperature change over time of thin liquid layer ′ s micro-cell can be achieved by infrared real time monitoring technique;

研究表明：红外实时监测技术可以清晰地观测到液膜的温度抖动特性，并且可以表征出液膜各微小区域之间的温度差异，以及各微小区域温度的实时变化；

Convection features in a thin liquid layer with heating sources is studied in the present paper.

研究一个液体薄层在热源作用下的流动特征。

A New Infrared Characterization Method of Acid Thin Liquid Layer over YBCO Film

表征高温超导YBCO薄膜表面酸性液膜特性的红外方法

Sugarbeet protoplasts were isolated from hypocotyl-derived callus ( SC3) and unpollinated ovule-derived callus ( SC1, SC2) respectively. Then the protoplasts were cultured in MSB ( 2) medium with shallow liquid layer.

从甜菜下胚轴愈伤组织SC3和未授粉胚珠愈组织SC1、SC2中分离到原生质体，在MSB（2）培养基中进行液体浅层培养。

A Study on Increasing Induction Frequency of Pollen Plants by Culture with a Thin Liquid Layer on Solidified Medium

固体培养基上浸润培养提高花粉植株诱导率的研究

As they ripen, a delicious soft-to near-liquid layer forms below the rind.

它们成熟时, 表层下面会形成绵软而近乎流体的一层,口味极美.

Investigation of Thickness Measurement of Liquid Layer in Mechanical Structure Using Ultrasonic Technique

机械结构液体层厚度超声测量方法研究

Among the culture methods involved in the experiment, thin layer liquid culture was the most suitable one.

在本实验所涉及的培养方法之中，以液体浅层培养为优。

Variation of temperature of liquid brass as well as preheating temperature and thickness of steel strip did not change the thickness variation pattern of cladding layer, but affected the holding time at individual stages and thickness of the cladding layer.

铜液温度以及钢带预热温度和厚度变化不改变复合层厚度的变化规律，但对各阶段的持续时间和复合层的厚度有影响；

High values area of integrated water vapor content and integrated liquid water content had a good consistency with the ground precipitation duration. ( 4) Before the sandstorm occurred, the temperature in low layer increased significantly and the temperature lapse rate was large.

积分水汽含量和积分液态水含量的高值区与地面降水发生的时间具有很好的一致性。（4）沙尘天气出现前，低层增温显著，高层降温剧烈，温度的垂直递减率较大。

A new type reboiler of horizontal, multi-layer, thin liquid film is developed, which is possessed of higher dispersing film efficiency and lower-height.

所用的新型卧式多层薄液蒸发釜，比立式降膜蒸发釜布膜率高，高度低。

Effect of Process Parameters on Interface Layer and Properties of Liquid Aluminum/ Steel

工艺参数对液态铝与钢界面层及其性能的影响

Determination of the content of oleanolic acid in the oral liquid 953 by thin-layer chromatography

薄层比色法对953口服液中齐墩果酸的含量测定

A silicon carbide shell is formed by the reaction of liquid silicon and carbon shell inner layer during sintering at 1500 ℃.

在1500℃烧结，液态硅与碳壳内层反应生成碳化硅层；

Using vacuum-evaporative pattern casting ( V-EPC) technology, the wear resistant surface cast iron can be gained by dipping the EPS model with the slime, casting and infiltrating the liquid iron to the slime layer.

采用真空实型铸造（V-EPC）法，在聚苯乙烯（EPS）泡沫模表面涂刷料浆，浇注后铁液渗入料浆涂层，得到表面耐磨铸铁。

Coating Layer Formation and Liquid-phase Penetration in Metered Size Press Coating

计量施胶压榨涂布中的涂层形成与液相渗透

The results showed the voidage ratio of taper spiral packing,θ-ring packing and metal gauze corrugated packing was 0.823:0.947:0.855, and under the same liquid sprayed density, the pressure drop ratio of unit height of packing layer was 0.58:1.10: 0.62.

流体力学性能测试中，锥度螺旋填料、θ环和丝网波纹填料三种填料的空隙率之比为：0.823：0.947：0.855时，在相同喷淋密度下，单位高度填料层压降之比却为：0.58：1.10：0.62。

The process of rotational foaming molding of liquid reactive resin was studied, with unsaturated polyester resin as the shell of unfoamed resin moulded part, and polyurethane as foamed core layer.

以不饱和聚酯树脂作为非发泡树脂成型制品的外壳，用聚氨酯树脂发泡形成泡沫芯层，研究了液体反应树脂的旋转模塑发泡成型泡沫夹层制品的工艺过程。

A multi layer coating with a SiW outer layer by liquid reaction formation method was prepared for carbon carbon composites, and then the structure of the oxide film on the coating was investigated by XRD, SEM, Raman spectrum and electron probe.

研究了一种液相法及其它方法制备的碳碳复合材料多层防氧化涂层，并用XRD，SEM，Raman光谱和EMPA研究了液相法制备的SiW涂层表面氧化后的结构。

Agarose block method is the best culture method, thin layer liquid culture method the second, and nurse culture method the third.

培养方法以琼脂糖小块培养法最好，液体浅层培养法次之，看护培养又次之。