liquid metal的例句大全

Acentric ingates are used to set on the moving mould and slag-collector is set at the end of ingate and at converging zone of liquid metal from two sides.

选择偏心的分支浇道，并将浇道设置在动模一侧。在浇道的末端和两侧金属液汇集区域分别设置集渣包。

The Principle of Gas Absorption and Slag Removal About Liquid Metal Having Through Sprue and Its Application

液态金属流经直浇道时的吸气、撇渣原理及应用

Under the control of the slide gate, the liquid metal for large ingot casting stored in the middle of the bag to keep heat.

这些金属液在滑动水口的控制下，汇集并贮存于中间包内保温，用于大型铸锭的浇铸。

plasma transferred arc produces the induced electromagnetic field that makes liquid metal convect in molten pool in the surface metallurgical course.

在表面冶金过程中等离子束产生感生磁场，使熔池内液态金属产生对流运动。

Experimental research on dephosphorization of high carbon liquid metal

高碳熔铁脱磷的实验研究

The most principal factors that influence the supersonic atomization process include the flow ratio of the gas-liquid metal ( GMR) value, the flow of atomizing of gas and the range of the inverse vortex taper.

影响超音速雾化工艺最根本的因素有气液质量流率比（GMR）的大小、雾化气体流量和倒涡流锥范围，三个因素的值越大，对形成细粉越有利；

Based on the physical design parameters of ITER and the results of the ( neutronics) calculation, the thermal-hydraulic design scheme for the Dual-function ( Lithium-Lead) Test Blanket Module ( DFLL-TBM) is presented. The pressure drops of the helium and liquid metal system are calculated.

依据ITER堆芯物理参数和中子学计算结果，给出了双功能锂铅实验包层模块热工水力学设计方案，并对氦气系统和液态金属锂铅系统压降和驱动功率进行了初步计算。

Magnetohydrodynamic experimental design and analysis for Chinese liquid metal LiPb experimental loop DRAGON-ⅳ

中国液态金属锂铅实验回路DRAGON-ⅣMHD实验段设计与分析

A novel liquid metal blanketing Cu center conductor post design for low aspect ratio Tokamak

低环径比聚变托卡马克液态金属包铜中心导体柱

This would guarantee a quick start and highly safe running of liquid metal for computer chip cooling.

该方法可确保液态金属循环快速启动和安全运行。

Study on Liquid Metal Flow and Impurity Removal inside Tundish

中间包内流体流动及夹杂物去除的研究

During in site extension in TEM without the liquid metal, only when dislocation emission and motion induced by thermal activity and applied stress reached a certain critical condition, microcrack would nucleate but not blunt into a void.

α-Ti在TEM中原位拉伸时，只有当热激活或外应力促进的位错发射和运动达到临界条件时，微裂纹才形核，并很快钝化成空洞而导致韧断。

Thermal Analysis of Directional Solidification Process with Liquid Metal Cooling

液态金属冷却法定向凝固试验的热分析

Negative Pressure of EPC's Liquid Metal Front Flowing's Relation That is About Membrane Thickness and Exothermic Coefficient

消失模负压铸造液流前沿气膜厚度与其放热系数的关系

Electric Field Calculation of Liquid Metal Ion Source Emitting System

液态金属离子源发射系统的电场计算

During the HPDC process, the filling behavior of liquid metal is very complex, which would cause flow marks, gas porosity, and lack of filling defects. Correspondingly the mold would get thermal fatigue cracks and erosion.

在压铸件成型过程中，金属液流动行为复杂，容易产生流痕、气孔、浇不足等缺陷，同时易于造成模具的热疲劳裂纹、冲蚀等，使模具的使用寿命缩短。

Due to the special properties of semi solid metal, lower processing temperature compared to that of liquid metal and lower yield strength compared to that of solid metal, it provide a possibility for the thermal precise forming of metal with high efficiency and low consumption.

由于半固态金属具有特殊属性，即加工温度低（与液态加工比）、变形抗力小（与固态加工比），为高效、低耗实现金属热精密成形提供了一种现实可能。

Effects of Thermal History of Liquid Metal Al on Its Solidification Microstructures

液态金属铝的热历史对凝固微结构的影响

The utility model relates to a sliding nozzle valve, which is a throttling device for pouring liquid metal.

一种滑动水口阀是注浇液体金属时用的节流装置。

However, owning to the harsh environment in which the magnetic confinement fusion reactor blanket and the exterior auxiliary system of fusion reactor works, the flow of liquid metal LiPb will bring a lot of challenging technical problems.

然而，磁约束聚变堆包层运行环境苛刻，液态金属LiPb在包层和堆外辅助系统中流动会带来很多具有挑战性的技术问题。