liquid phase的例句大全

Determination of Heavy Metal Element in Water Samples by Solid Phase Extraction Concentration High Efficiency Liquid Phase Chromatography

固相萃取富集高效液相色谱法测定环境水样中的重金属元素

The newly developed technology for dimethyl sulphoxide production from dimethyl thioether with the catalysis of NO2 and the method of oxidation in emulsive liquid phase has been narrated in the article.

阐述了二甲基硫醚在二氧化氮催化下，采用液相乳化氧化法生产二甲基亚砜的新工艺。

The density of tungsten heavy alloy plates liquid phase sintered in continuing furnace was investigated with drainage, and its distributions both in width and length were studied.

采用阿基米德排水法，测量了连续液相烧结钨基高比重合金板的密度，并对其在长度和宽度方向上的密度分布进行了研究。

The developed simulation platform is applied to simulate the reactive distillation process of dehydration of tert-butyl alcohol where the unstable of liquid phase is considered.

本文应用所开发的联用模拟平台对叔丁醇脱水制异丁烯的反应精馏过程进行了模拟分析，并在过程模拟时考虑了该体系的液相分层因素。

Effect of Distribution Constant and Gas Liquid Phase Ratio on Sensitivity of Static Headspace Gas Chromatography

分配常数及气液相比对顶空气相色谱分析灵敏度的影响

The discussion on acting mechanism of the catalyst material is actually the study of the process for fostering crystals from melten solution. The main driving force which produces the process is the thermodynamic potential difference between diamond and liquid phase.

讨论触媒材料的作用机构，实质上是研究从熔融溶液中培育晶体的过程，金刚石与液相的热力学势差是过程进行的主动力。

Meanwhile, the most difficult task for simulation and optimization of heterogeneous distillations is to determine whether the liquid phase is stable in column stages or packing sections, which is also one of the focuses of this dissertation.

在三相共沸精馏过程建模仿真和优化计算中，由于两个液相可能同时出现，判断液相稳定性问题已成为了一个三相精馏过程计算的瓶颈问题，这也是本文的研究重点之一。

Distortion of PIM tungsten heavy alloy during liquid phase sintering

PIM高密度合金在液相烧结过程中的变形

Detritiation From Heavy Water by H_2-H_2O Liquid Phase Catalytic Exchange

氢-水液相催化交换法脱氚

It includes the main principle of carbon/ carbon composites prepared by densification technology of rapid liquid phase deposition, the design of technology process, the calculation of technology parameters by theoretical chemistry and microstructure of carbon/ carbon composites.

内容包括：快速液相沉积致密化工艺原理、致密化工艺过程的设计、工艺参数的计算化学理论确定方法，以及用该工艺制备的碳/碳复合材料及其微观结构研究。

In this paper, benzoic acid refining distillation system with SNIA benzene liquid phase process was researched via simulation. The effect of theoretical tray numbers 、 operation pressure 、 reflux ratio 、 feeding position etc.

本文对SNIA甲苯液相法生产苯甲酸产品精馏系统进行了研究，考察了三个精馏塔的理论板数、操作压力、回流比、进料位置等条件对SNIA苯甲酸产品质量的影响。

Direct Lixiviation and Oxidation in Liquid Phase-New Technological Process for Preparation of High-quality Zinc Oxide

液相氧化直接浸出制取高级氧化锌新工艺

The process, technological principle and characteristics of preparation of nan particles in solid phase, liquid phase and gaseous phase are generally reviewed.

文章较全面地概述了纳米颗粒固相、液相和气相的制备方法及工艺原理和特点。

The vapor-liquid phase equilibrium data for the binary system of m-xylene-water at 0. 1013 MPa were determined by using an improved pant equilibrium cell. Thermodynamic consistency test indicates that the experimental data are reliable.

采用改进的Partt釜测定了在0.1013MPa下，间二甲苯－水二元部分互溶体系的气液相平衡数据，经热力学一致性检验表明，测定数据是可靠的。

Simulation of Transient Liquid Phase Diffusion Welding Temperature Field by Finite Element Method

瞬时液相扩散焊焊接温度场有限元模拟

It was found that the thickness of diffusion layer was in direct proportion to the square root of time, and varied with temperature index at the same temperature, before the liquid phase formation.

得出在界面处液相出现（即达到共晶或进入固液共存区）之前，扩散层随温度按指数规律变化；在同一温度，扩散层与扩散时间的平方根成正比。

By the stress and corrosion condition analysis of tube-plate, the tube-plate is borne tension stress under superimposition of the welding residual stress, thermal stress, vibration induced by gas-liquid phase flow and the assembly stress.

分析油浆换热器管板受力和腐蚀环境：管板在焊接残余应力、温差应力、气-液两相流的诱导振动及装配应力的相互叠加作用下，受拉应力；

Transient liquid phase ( TLP) bonding was applied to join TP304H stainless pipe, and the effect of bonding temperature on joint microstructure and mechanical properties was studied.

采用瞬时液相扩散焊（TLP）连接技术进行了TP304H不锈钢管的焊接，分析了不同焊接温度对接头组织、成分和力学性能的影响。

At vacuum and above mentioned temperature, a firm joint can be formed between ceramic and metal by a active liquid phase alloy formed on copper surfaces to wet ceramic.

在真空、温度的作用下，陶瓷与金属之间藉助于铜表面本身形成的液相活性合金，润湿陶瓷而获得牢固的连接。

Testing for Transition Liquid Phase Diffusion Bonding of Turbine Guide Vanes

涡轮导向叶片过渡液相扩散连接工艺试验