load circuit的例句大全

The main circuit diagram of energy feedback electronic load is proposed, and explains the design specifications, and design feasibility was proved by MATLAB simulation. Finally, the paper analysis the reliability of system design.

给出了能馈型电子负载系统的主电路图，说明了设计规格，并通过MATLAB仿真试验证明了设计的可行性。

Based on the characters of the current controlled technique, the author presents a new electronic load for constant current discharging and a two steps charging circuit for aviation batteries using PWM current controlled two state modulation technique.

根据电流控制技术的特点，着重介绍用PWM电流调制技术实现航空蓄电池恒流放电的新型电子负载和航空蓄电池两阶段充电控制电路。

Aiming at the load characteristics of the potentiometric type sensor, presents a potentiometer measuring circuit with compensating potentiometer and compensating load resister and analyses its characteristics.

本文针对电位器传感元件的负载特性，提出一种带有补偿电位器和补偿负载电阻的电位器测试电路，并对其特性进行了分析。

The electronic load is a new power electronics device that can simulate the loads of the circuit in the testing and test power supply performance.

它是一种可以模拟供电器负载，用来测试供电器性能的新型电力电子设备，它广泛的用于各种供电设备的保养，老化试验，出厂试验，型式试验。

Double balance Gilbert-cell incorporating a capacitively-source-coupled current amplifier and a single-tuned tank as load is utilized to improve the circuit performance.

该电路采用改进型双平衡Gilbert单元的结构，引进了容性源极耦合差动电流放大器和调谐负载电路，大大提高了电路的性能。

Therefore choose positive and negative voltage regulating scheme as main circuit wiring scheme of on-load tap changer.

因此最终选择了正反调压方案作为有载分接开关的主电路接线方案。

This paper analyzes the influence of the error of the transformer normal tapping ratio, short-circuit resistance and the load of plant power supply on parallel operation, and calculates the difference between the allowable loads for different units while parallel operation conditions are satisfied.

文中分析了变压器变比误差、短路阻抗对并联切换的影响，计算了满足并联切换条件时机组间的允许负荷差异。

in a conclusion, the fai system can completely remove the fuel short-circuiting, and greatly improve the performance during heavy load operating conditions.

总之，FAI缸内直喷技术，可以完全消除二冲程汽油机的燃油短路的现象，极大地改善二冲程发动机性能。

the hardware part design including fault injection unit and simulation load design, and the fault injection unit includes four modes: normal mode for the signal, the open circuit mode, connect to power mode and connect to ground mode.

在硬件方面是主要设计故障注入模块和模拟负载的设计，故障注入主要包括四种模式：信号的正常模式、断路模式、对电源短接模式以及对地短接模式。

algorithm realization based on the load characteristics of beam-pumping unit and phase-failure protection circuit

基于游梁式抽油机负载特性的算法实现与断相保护电路

overvoltage limiting for vacuum circuit breaker when breaking off non-loaded transformer

真空断路器断开空载变压器的过电压限制

non-load and steady state shout-circuit performance measurement for generator and exciter

发电机和励磁机空载特性和稳态短路特性测量

the testing results and the calculating results of the perameters such as no-load loss, no-load current and short-circuit impedance of several 240mva/ 220kv double-winding step-up transformers are compared and analyzed. the experienced coefficients of the parameters are given.

对几台240MVA/220kV双绕组升压变压器的空载损耗、空载电流和短路阻抗这几个重要参数的试验数据和设计计算值进行了比较与分析，得出了这些参数的一些经验系数。

the calculation results of eddy current distributions in end structures, such as copper shield plate and retaining ring, under a no-load 3 phase sudden short circuit situation are presented.

得到了在三相空载突然短路情况下端部结构件（银屏蔽、转子护环等）中的瞬态涡流分布。

developed distribution transformer data collection terminal, which realizing transformer harmonic current signal conditioning, digital collection, fft spectrum analysis, remote data transmission and can provide data for analysis capacity, non-load loss and short-circuit loss of distribution transformer.

研制配电变压器数据采集终端，实现谐波电流的信号调理、数字化采集、FFT频谱分析以及远程数据传输，并且可以为配电变压器容量、空载损耗和短路损耗的在线监测提供分析所需数据。

the converter has many advantages, such as simple circuit structure, high efficiency at full load and low loss at no load.

整个电路结构简单、满载效率高、空载损耗小。

the problems of amorphous alloy distribution transformer, such as the core structure, no load loss, noise, anti-short circuit ability, technical and economic questions, were mainly analyzed.

分析非晶合金配电变压器的铁心结构、空载损耗、噪声、抗短路能力、技术经济性等问题。

the driving circuit of stepping-motor with the function of over-load protection and short-circuit protection is established; the accurate control characteristic of open degree of eev is realized by the way of driving stepping motor directly and four-phase-eight-pat controlling pattern.

设计了具有过载保护与短路保护的步进电机驱动电路，采用PLC直接驱动步进电机驱动方式与四相八拍控制方式，实现对电子膨胀阀开度的精确控制。

the short circuit protection should be tested at other load rating.

短路保护测试是在其它额定负载时测试。

the impedance matching circuit is used for improving the load capacity of the circuit so as to improve the pulse ultrasonic wave form;

所述阻抗匹配电路用于提高电路的负载能力，改善脉冲超声波形；