load deformation的例句大全

At the same time, the load deformation curve of the outer wall of the flexible wheel was analyzed by load simulation. ( 3) Structural design and solid modeling of each major component of the giant magnetostrictive harmonic motor.

超磁致伸缩谐波电机各主要构件结构设计及实体建模。

Off load rock mass of excavated slope can be divided into 3 zones: surface loose zone, off load deformation zone and stress adjustment zone.

开挖边坡卸荷岩体可为3个带：表层松动带、卸荷变形带以及应力调整带。

Bearing capacity analysis of self-balanced load test pile under the control of limit state and deformation

极限状态及变形量控制下自平衡试桩承载力分析

During the bearing turning, the body of the bearing testing set receives the bigger load and generates larger deformation and stress.

在轴间轴承测试过程中，试验机机体承受较大的载荷并产生一定的变形和应力。

The large deformation is mainly due to rock properties, unsymmetrical load and tectonic effect of the Yunxi-Yunxian fault.

结果表明，导致大变形发生的原因主要是岩性、偏压和两郧断裂构造作用等。

Based on gradient-dependent plasticity where an internal length parameter is included to consider the microstructural effect, the distributions of shear deformation, shear strain and temperature in adiabatic shear band were derived considering the slow and sharp decrease of load-carrying capacity beyond the peak shear stress.

采用梯度塑性理论，考虑了峰值剪切应力之后的材料承载能力缓慢降低的过程及承载能力快速降低的过程，推导了剪切带内部的剪切变形、应变及温度分布的公式。

It worked out the tensile stress-strain curve, the load-displacement diagram, the maximal stress distribution figures and the crack history figure during the deformation and failure process of the concrete specimen.

数值模拟结果给出了混凝土拉伸应力-应变曲线和三点弯曲载荷-位移曲线，以及混凝土试件破坏过程最大应力分布图和裂纹扩展图。

Entire control system assay the PCI card computer bus controller, achieved on the test load, deformation, displacement digital zero and gain adjustment, easy to operate, offers high reliability.

其整个测量控制系统采用试金PC工一卡通计算机总线式控制器，实现了对试验力、变形、位移零点和增益的数字化调整，操作方便，具有极高的可靠性。

Analysis on bolt strain with large deformation under shearing tensile load

锚杆拉剪大变形应变分析

This paper describes that the failure tensile load and deformation were tested by the specimens which were made from carbon-fiber fabrics and epoxy resin.

本文把单向碳纤维无捻布和环氧树脂制成复合材料试样，测试出其拉伸破坏载荷和变形；

As to K-shape joint under design load, while the main tube is in tension, the joint bearing capacity increases as the joint deformation escalates, and the joint has good ductility;

对于K形节点：主管受拉时节点的承载力随变形的增大而不断增加，节点有很好的延性；

It obtains the deformation and failure mechanism of the steel skeleton reinforced HDPE under tension and bending load conditions.

钢网增强HDPE复合材料的受拉伸与弯曲载荷条件下的形变与破坏机理。

Load and deformation analysis of pedestal tension pile

扩底抗拔桩荷载变形分析

Load-transfer method is adopted to analyze the relationship between lad and deformation of pedestal tension pile.

采用荷载传递方法，建立了扩底抗拔桩的分析模型。

Comparatively speaking with the compressive pile, Our knowledge about the Load-bearing mechanism and Stressed deformation of tension pile are far behind.

相对抗压桩而言，人们对于抗拔桩的承载机理与受力变形的认识却远远落后于对抗抗压桩的认识。

The stress of base structure is analyzed by3-D FEM under the action of temperature warping deformation and coupling with vehicular load.

方法结合试验路温度场监测数据，采用三维有限元法对基层结构在温度翘曲变形及与车辆荷载耦合作用下的受力特性进行分析。

The stress and deformation under elastic-plastic behavior are given for the structure of combined thick cylinder, and the simple deformation on the influence of structural plastic limit load is discussed.

给出了组合厚壁圆筒结构在弹塑性状态下的应力及变形情况，并且论述了筒体变形对结构塑性极限荷载的影响。

As an example, the oil film pressure, the elastic deformation and the static performance of a tilting-pad thrust bearing in heavy-loading condition are calculated by using the out-domain method.

作为算例，用域外法联立求解雷诺方程和弹性变形方程，计算了大型可倾瓦推力轴承的油膜压力、弹性变形和相应的静特性参数。

After being set state load, optimized timbering adds support yielding deformation, increases the load-carrying ability and improves the effect of controlling the surrounding rock.

在给定初始支撑强度的前提下，加大支架的让压变形量，提高支架承载能力，大大改善了矿工钢梯形支架控制围岩的效果。

Finite element program of non-linear analysis to pile is made and together with results of building test pile and model test pile, therefore, the feature of load transferring and deformation mechanism were deeply analyzed.

对工程试桩的静载试验结果进行分析，确定单桩极限承载力。室外模型桩试验通过在桩身埋设测试元件，研究水泥土组合桩荷载传递规律以及变形特性。