load voltage的例句大全

at rated voltage and rated load ( vibration weight).

在额定电压和额定负载（振子）下。

modification to the formula for calculating load rating of three-phase induction motor on the non rated voltage condition

三相异步电动机负载率计算公式在非额定电压条件下的修正

but the parasitic capacitance existed in gis bus line will append lots of condensive load in the rated voltage, so when testing the gis bus line voltage transformer, the booster is not allowed.

但在测试GIS母线电压互感器时，由于GIS母线存在的寄生电容在额定电压下将附加大量的容性负载，因此不允许使用试品升压。

The unique "Medium voltage motor drive full load test center" in China.

荣信公司建有国内唯一的各项试验条件完备的中压变频全载试验中心。

For the second strategy, a voltage controller and a current controller were designed by the active disturbance rejection control ( ADRC) technique, and the corresponding control system manifests high robustness in rejecting disturbances from the load and some other parameters.

在第2种控制策略中，采用自抗扰控制技术设计了电压和电流控制器，控制系统对负载扰动和参数扰动具有很强的鲁棒性。

the voltage output is supplied to a load, for example, the word line of an eprom memory circuit.

将电压输出供应到负载，例如EPROM存储器电路的字线。

in order to drive a high impedance load such as hpm sources, it is necessary to commutate fcg's long pulse width, high-current and low voltage pulse to a short pulse with high voltage.

为用FCG驱动象HPM源这样较高阻抗的负载，必须使用脉冲功率调制电路把FCG产生的低电压、大电流、上升时间长的电压脉冲转化为高电压、上升时间短的脉冲。

for many application cases, such as voltage adjustment and power flow matching, methods based on bus-type extended load flow calculation can be effective.

对于电网电压调节和潮流模型匹配等许多应用场合，可采用基于节点类型扩展的潮流计算方法。

the application for bus-type extended load flow in voltage adjustment and network power flow matching was studied in this paper.

研究节点类型扩展潮流计算方法在电网电压调节和潮流模型匹配中的应用。

study on sensitive dynamic load modelling during voltage sag process

电压暂降过程中敏感动态负荷建模问题研究

A technique to prevent this is load shedding by rolling blackout or voltage reduction brownout.

一种技术,以防止这种情况是由轧制负荷减少停电或电压(掉电)脱落.

Busbar load characteristic parameters play avery important role in voltage stability analysis.

母线负荷特性在电压稳定性分析中有着重要的作用.

A separate-controlled AC-DC-AC power load simulator is designed adopting the principle of voltage type PWM convertor.

本文运用PWM电压型变流器的基本原理,设计了一种分离 控制式 交 - 直 - 交功率负荷模拟器.

DC capacitor relies on the pulsation of DC voltage, power, inductance side, and load.

突加负载时直流侧电容是由直流电压波动 、 功率 、 电感及负载决定的.

When an inductive load is connected to a voltage source, the current will increase relatively slowly.

当一个电感性负载被连接到电压源时, 电流上升速度相对较慢.

This is generally measured under full load at nominal line voltage.

通常是在满负荷额定线电压下测定的.

When ordering overload relays, specify horsepower, voltage and full load current per motor nameplate.

订购过载继电器时, 请注明每台电机的功率马力 、 电压和满载电流.

Alternatively a shunt is used to prevent overcharging once the load reaches the predetermined voltage.

或者,使用分路来防止一旦负载达到预定电压就发生过充电.

Note : The power supply shall be test at Max voltage ( 265 Vac ) and min load no load.

应该在最大交流输入电压 265 伏和轻载、空载下测试.

No load tap ranges should be selected to provide an adequate low-side bus voltage.

无载分接范围选择应能提供正确的低压侧母线电压.