lock plate的例句大全

24 of them were treated with fusion using autogenous iliac bone graft and self lock plate internal fixation; 2 were treated with cage implant with vertebral cancellous bone.

方法对26例60～81岁老年人脊髓型颈椎病患者行颈前路开槽式减压，24例取自体髂骨移植，并行带锁钢板内固定，2例用Cage内充填减压椎体之松质骨植入。

equipped with a boast fast lock plate and frame, you can quickly order.

配有博斯特快锁板框，可快速换单。

For titanium plates and screws in A and C zone intercalary endoprosthesis. the lock mode can be adopted. Meanwhile, the thickness of the titanium plate and the screw diameter can be enhanced so as to reduce risks of screw detachment and endoprosthesis fracture.

对A、C区节段型人工假体的钛板和螺钉可设计为锁定模式，同时适度增加钛板增厚、螺钉的直径以减少螺钉脱出和假体断裂的风险。

Calculation of the Elasto-Plastic Limit Bearing Capacity for the Face Plate of Steel Lock Gates

钢闸门面板弹塑性极限承载力计算

Clinical study of the treatment of proximal humerus fractures with locking-compression plate

LCP治疗肱骨近端骨折

Loosen and remove the diaphragm lock nut and lock washer, pressure plate and diaphragm from the valve stem.

松开和拆卸隔膜锁紧螺母和锁紧垫圈，从阀杆上往下压阀盘和隔膜。

Coded lock components ( 30) are disposed on an outer lock hole ( 202) of the safety lock of an outer door plate as well as on an outer lock hole ( 152) of the remote control lock.

并且在外门板的保险锁的外锁孔（202）和遥控锁的外锁孔（152）上设有密码锁组件（30）。

The reversed tainter valve of double plate type will be used in the TGP's lock filling and emptying system.

三峡船闸输水系统阀门设计拟采用双面板式反向弧形门。

the clamping ring is circular and is fixed on the upright post through a connecting plate and the lock bolt.

卡环为圆形，通过连接板和锁紧螺栓固定在立柱上。

align the hex plate with the receiver on the head and gently press down until the lock clicks into place ( figure 13 ) .

然后将六角形快装板与云台上的对应处对齐，接着轻轻按下直到锁紧（图13）。

doors for rail vehicles; edge strips around the lock plare and striking plate

有轨机动车辆用门.锁侧闭合边条

after an analysis of the disadvantages of the three types of casing heads-the annular plate, the simple and the normal casing heads, the st lock tightened casing head was innovated by huabei oilfield.

通过对环形钢板、简易套管头和正规套管头三种井口装置在使用过程中弊病的分析，华北油田研制成ST锁紧式套管头。

the plate element is the eight-node arbitrary quadrilateral element based on the mindlin hypothesis, the reduced integral is introduced to avoid the shear-locking problem of the mindlin plate element.

板单元是基于Mindlin假设构造的八结点任意四边形单元，采用减缩积分方法避免了Mindlin板单元固有的剪切锁死问题。

Machinery self-lock and heavy load bearing plate type of chain lifting system. High safety performance guaranteed.

机械式自锁,重负荷承载板式链条举升系统,安全性能高.

The analytical trial function method was used to extend the existing Kirchhoff triangular thin plate element, to the corresponding lock-free Mindlin triangular thick plate element.

为了有效克服剪切闭锁问题，利用已有的薄板单元构造厚薄板通用单元，提出了采用解析试函数法（ATF），将已有的Kirchhoff三角形薄板单元推广为相应的Mindlin三角形厚板单元的通用方法。

Based on the principle of plate roll forming, a lock joint former is developed.

运用板料滚压成形原理, 设计研制了通用的咬缝成型机.

Locking-free Thick Plate Bending Triangle Element

完全无闭锁厚薄板通用弯曲三角形单元