main controller的例句大全

This part includes the FPGA realization of the main controller as well as various functions modules of hardware system, such as the design of MEL-STD-1553B protocol controller module, RS-422 conversion module, FPGA configuration module, power module and so on.

本部分内容包括主控制器的FPGA实现分析以及系统硬件各功能模块如MIL-STD-1553B协议控制器模块、RS-422电平转换模块、FPGA配置模块和电源模块等的设计。

Implemented that main controller communicated with collecting data module according to RS-485 communication protocol.

并按RS485通信协议实现了数据采集模块和主控制器的通信。

The core of automobile black box system is its main controller.

汽车黑匣子控制器系统的核心部分是主控制器。

In the main controller module section, it discusses the circuit design of the main controller and the matters need attention when initialize it.

在主控制器模块，论述了主控制器硬件电路设计和初始化过程中的注意事项。

In addition, in the main controller hardware composition. of the node, it also uses the acquisition terminal hardware circuit, but only uses the wireless transmission parts of the acquisition control terminal.

另外，在主控制器节点的硬件组成中，它还使用了采集控制终端设备的硬件电路，但具体设计时仅仅使用了采集控制终端的无线传输部分。

In hardware aspect, the freezer controller were consisted by main controller, temperature detection module, control output module, display and alarm module, temperature storage module, wired communications, wireless communications, and other functions.

在硬件方面，该冷柜控制器包括主控制器、温度检测模块、控制输出模块、显示与报警模块、温度存储模块、有线通讯、无线通讯等功能。

Completed the design of the "Longtium D2" L2 cache, including the architecture design, hardware support, interconnection mechanism and the state machine of main controller etc.

完成了龙腾D2双核处理器中二级Cache的设计，包括整体结构的设计、硬件支持、互联机制、主控状态机的设计等。

Concentrator design includes the main controller, power supply circuit, memory cell, the clock module, GPRS module and interface circuit.

集中器的设计包括主控制器、电源电路、存储单元、时钟单元、GPRS模块和接口电路构成。

Twist type surface of robot numeric control auto search plasma quenching system consists of main controller, industry robot, plasma quenching welder, two clamping clip tight devices and laser displacement sensor, etc.

扭型曲面的机器人数字控制自动搜寻等离子淬火系统，由主控计算机、工业机器人、等离子淬火焊机、2套定位夹紧装置和激光位移传感器等组成。

Study and Development of Main Controller Unit In Short-Wave Radio Station

短波电台主控制器单元的研究与发展

Traditional single-stage PFC converter usually adopts analog control, however with the rapid development and the drop of the price of the digital signal processor, more and more power electronic equipment use DSP instead of analog controller as the main controller.

传统的单级功率因数校正变换器通常采用模拟控制，随着数字信号处理器（DSP）的飞速发展及性价比的进一步提升，越来越多的电力电子设备采用DSP取代原有的模拟控制芯片作为主控制器。

The communication software of the main controller is designed, and using addressed data frames, the conflict of serial communications has been solved.

设计了主控制器与其它模块通信的软件，采用带地址的数据帧通信格式，解决了多路串行通信的冲突问题。

The general ATE system in weapon support consists of UP pc main controller, VXI general apparatus module, signal bestirring source, signal adjusting and interface circuit.

应用于武器保障的通用ATE系统，由上位机主控制器、VXI通用仪器模块、信号激励源、信号调理和接口电路组成。

The designed system includes nodes in three-level structure: main controller, group controllers and switch nodes.

整个系统采用主控制端、组控制端和开关节点三级结构。

In this scheme, the proposed PSS consists of main controller, self-organizing controller and slide mode controller.

在该控制策略中，电力系统稳定器（PSS）由主控制器、自组织控制器和滑模控制器三部分构成，其中，主控制器用于产生PSS的基本输出信号；

A main controller is not required, and it handles up to16 terminal controllers per Ethernet connection.

主控制器不是必需的，它能处理每个以太网连接的多达16个终端控制器。

This paper not only introduces a structure of stimulating magnetic controller with double CPU and it's working principle, but also presents the communication method of double CPU and the particular design method of using display controller as well as the main controller's 'watch dog'.

介绍双CPU励磁控制器的结构、工作原理，给出双CPU间的通信方法，阐述了采用显示控制器兼作主控制器的看门狗的独特设计方法。

A GTO dc chopper is adopted for the main power supply while the switch mode control with derivative feedback loop is adopted for the main controller.

主电源采用GTO直流斩波器。主控采用带微分反馈环节的开关斩控模式。

Main controller use two shift register to control LED lights, digital tubes, buzzer realize local display and alarm.

主控制器通过两个移位寄存器来控制LED灯、数码管、蜂鸣器实现本地显示与报警。

Then, through the moving parts of the step-motor working principle, using SCM as a main controller to put forward the CNC Stop-motion Animation Photography System and based on this, the main specific designs on electrical circuits in every module will be followed.

随后，基于步进伺服驱动技术开发了单片机为主控制器的数控逐格拍摄控制系统，对其中主要模块的电路进行详细的设计。