main load的例句大全

Mega structure is a new structural system of super high-rise building. Due to distinct load-transform path and flexible arrangement of main structure and subordinate structure, mega steel fame can be used to satisfy special building forms and functions.

巨型结构是一种新型的超高层建筑结构体系，结构体系的主、次结构受力明确，布置灵活，可满足特殊的建筑形式和建筑功能的要求。

This dissertation is derived from the project of the National Science Foundation of China "Research on Electro-Hydraulic Control Theory and Engineering Realization for Construction Machinery with Long Hydraulic Pipeline" and the load sensing system is considered as the main subject investigated.

本文源自国家自然基金资助项目带长管道的工程机械电液系统控制理论及其工程实现研究。

Wind load and inertia load are the main factors that affecting mobility and stability-board for vehicle radar.

风载荷和惯性载荷是影响车载雷达机动性和工作稳定性的主要载荷。

Energy saving, environmental protection and safety are main concern of modern automobiles. Because of more and more electrical equipment and load, using a new 42V vehicle-borne power supply system to replace the existing 14V power supply system will be inevitable.

在以节能、环保和安全为中心的现代汽车中，电气设备越来越多，电气负荷越来越大，用新的42V车载电源系统取代现有的14V电源系统将是大势所趋。

the axial clearance is one of the main parameters of the rolling bearing; measured clearance value is closely related to the measuring method and load.

轴向游隙是滚动轴承的关键指标参数之一，测量方法、测量载荷与测得的游隙值的大小密切相关。

In-furnace average temperature correlates relatively well with boiler load and main steam pressure.

炉内平均温度与机组负荷和主汽压力的相关性较好；

Then the stress, deformation and fatigue of main bearing wall were checked in different load condition. And the area prone to fatigue damage was found.

其次对机体主轴承壁强度进行计算分析，考核它在不同工况下应力分布、主轴承孔变形以及疲劳强度，找到容易发生疲劳破坏的区域。

The main works in this study are including: 1. To gain the load-displacement and load-strain curves by the measurement technique of displacement and strain using displacement sensors and strain gages on the six test vessels with different d/ D ratios under different loads.

在不同的接管纵向弯矩作用下，对不同结构尺寸的正交接管容器进行试验研究，测定结构关键部位的应变值和接管位移，通过绘制载荷位移曲线和载荷应变曲线研究其极限载荷。

The simulating result showed that when the unit load changes, the maximum dynamic difference of main-steam temperature drops 13.8%, the regulating time shortens 17%, and the control character is improved well.

仿真结果表明，在机组发生负荷扰动时，主蒸汽温度的最大动态偏差降低了13.8%，调节时间缩短了17%，其调节品质明显改善。

Results show that the poor lubrication condition during the working of the diesel engine acts as the main reason for sinter. When the lubricating oil is insufficient, friction heat rises, which causes the crankshaft and the bearing shell bear very high thermal load.

研究结果表明，烧瓦的原因主要是润滑条件不良，摩擦热量增多，曲轴与轴瓦都承受很高的热负荷，最终导致烧瓦。

The paper introduces main technical measures of ship pneumatic control lift off load system improved and application effect.

介绍了箕斗气控卸载系统改造的主要技术措施及运用效果。

The main difference between various bogie frame is the structure and parameters of spring suspension system 、 the method of load transfer along vertical and lateral 、 the supporting of wheelset 、 the location of axle-box and the type and fixing of arresting gear and so on.

各种转向架构架的主要区别在于弹簧悬挂系统的结构与参数、垂向与横向载荷的传递方式、轮对支承方式、轴箱定位方式和制动装置的类型与安装等诸多方面。

Directing the Yellow Project GM3 Pumping Station Main Equipment Load Efficiency Analysis

引黄工程GM3泵站主要设备负荷效率分析

After deboned, the faceplates occurred the permanent bending deformation and elastic buckling in the vertical main direction of compression load, and the foam core happened the shear failure and permanent plastic deformation.

上下面板和泡沫夹芯脱胶分离后，面板主要垂直于压缩载荷的方向发生弹性屈曲和永久的弯曲变形，泡沫夹芯在冲击损伤的附近发生剪切失效和永久的塑性变形。

The following are the main research procedures and achievements: 1. Introducing the basic method for analyzing the structure flection load by finite units and giving a computer program. 2.

论文的主要研究工作与成果如下：1.介绍了有限元分析结构屈曲荷载的基本方法，并编制了程序。

However, for performance alone, in V8 it's usually better to use load directly into the main table, because load doesn't have the concurrency restrictions it had in V7.

不过，单单就性能而言，在V8中还是使用load直接将表装载到主表要快些，因为在V8中的load不像V7中那样有并发限制。

When load is between 15% and 25%, feedwater control valve is closing at fixed speed determined by function module, main motor-operated-valve is opened automatically, control mode of drum level is transferred to feedwater pump automatically and bumplessly;

15%至25%负荷阶段，给水调节阀由函数模块按照一定的速率自动平滑关闭，主给水电动门自动打开，汽包水位控制方式自动无扰切换为给水泵自动控制；

The main circuit diagram of energy feedback electronic load is proposed, and explains the design specifications, and design feasibility was proved by MATLAB simulation. Finally, the paper analysis the reliability of system design.

给出了能馈型电子负载系统的主电路图，说明了设计规格，并通过MATLAB仿真试验证明了设计的可行性。

Both units ( 2X300MW) of one power plant in India, designed and constructed by China, employ feedwater system composed of three 50% capacity motor driven feedwater pumps, one low load feedwater control valve and one main motor-operated-valve.

由我国承建的印度某电厂两台300MW发电机组，其给水系统设三台电动调速给水泵、一个低负荷给水调节阀（用于低负荷水位控制）和一个电动主闸阀。

Its main products include pulling tool, spring tester, measuring tool, image measuring apparatus, load curve measuring tool and paper tape punch, and other instruments.

公司主要销售有拉力计、弹簧测试仪、量具、影像测量仪、荷重曲线仪及纸带机等仪器设备。