martensite lath的例句大全

As the peak temperature of thermal simulation, which was higher than Ac3, increased, the prior austenite grain size and the martensite lath size increased, and consequently the impact toughness depressed.

模拟热循环的峰温高于Ac3时，随着峰温的提高，奥氏体晶粒明显长大，马氏体板条尺寸也相应增大，因此冲击韧性相应下降。

The main microstructure features of fatigue failure are martensite lath or martensite packet.

疲劳断裂的基本组织单元为板条晶或板条束。

The test results showed that Nb could prevent recrystallization of deformed lath martensite structure at 600~ 680 ℃, and the aged structure was tempered sorbite kept lath martensite phase direction with no ferrite particles discovered.

试验结果得出在600～680℃范围内，Nb能阻止变形马氏体组织的再结晶，时效组织主要为保持板条马氏体位向的回火索氏体，未发现粒状铁素体。

The microstructures of heat affected zones of T91/ 10CrMo910 are tempered sorbite and thin tempered lath martensite and the toughness is good.

10CrMo910热影响区和T91热影响区的组织分别为索氏体和细的回火马氏体，韧性较好。

Macroscopic Lattice Deformation Characteristic and its Crystallographic Analysis of Lath Martensite Transformation

板条马氏体的宏观点阵变形特征及其相变晶体学研究

Effect of Lath Martensite Morphology on the Mechanical Properties of Steel

条状马氏体形态对钢力学性质的影响

The Effect of Microstructure on Crack Initiation and Steady State Propagation of Lath Martensite

微观结构对板条马氏体启裂和裂纹稳态扩展的影响

The microstructure of surfacing metal is lath martensite and carbide.

堆焊层显微组织为低碳马氏体和碳化物。

They are dislocated lath martensite area and twinned martensite area respectively.

这些微区分别为内孪晶马氏体区和位错板条马氏体区。

At high temperature and low strain rate, the lath martensite reorientates to the loading direction.

当试验温度较高且应变率较低时，伴随有马氏体板条向拉伸方向偏转的细观特征。

The microstructures of the steel are fine lath martensite after "zero time holding" quenched.

零保温淬火后可获得细小的板条状马氏体组织。

The microstructure evolution and grain-refining mechanism of the process, severe rolling of lath martensite, was studied.

分析了采用板条马氏体大变形轧制工艺制备超细晶钢板时的显微组织演变过程及其晶粒细化机制。

Grain-Refining Mechanism of Severe Rolling to Lath Martensite

板条马氏体大变形轧制工艺的晶粒细化机制

the morphology of martensite of the steel is the shape of lath, and there exist films of retained austenite between lathes.

淬火组织为板条马氏体，马氏体板条间存在残余奥氏体薄膜；

These lath martensite first nucleates in parent austenite intergranular and twin boundary.

应变诱发马氏体首先在原奥氏体晶界和孪晶界形核.

The result indicates that there was a great deal of lath martensite in the quenched structure.

显微组织中存在大量板条马氏体,组织亚结构中存在大量位错和孪晶.

The results show that there are four kinds of carbides in annealed state of the steel, and major portion of quenched martensite is lath-like martensite.

结果表明，该钢退火状态存在四种类型碳化物，淬火组织以板条马氏作为主。

The results show that, the microstructure of the alloy is of lath martensite, with granular carbide dispersed in matrix, the alloy has high strength, toughness and temper resistance.

结果表明：该钢的显微组织为板条马氏体，且基体上弥散分布着粒状碳化物，具有高强韧性、抗回火稳定性；

A STUDY OF GRANULAR DESULFURIZER MADE FORM BOG IRON ORE Shape and Crystallography of Lath Martensite

板条状马氏体形态和晶体学

After normalizing+ tempering twice, all samples are composited of lath tempered martensite and dispersed reverse austenite. The tempered martensite content gradually reduce with the increase of the titanium, and reverse austenite content increase.

试样经过正火+两次回火热处理后，组织由板条回火马氏体和弥散分布的逆变奥氏体组成，回火马氏体随含钛量增加逐渐减少，逆变奥氏体逐渐增加。