maximum displacement的例句大全

with increasing water depth, the maximum displacement, velocity and acceleration of bridge mid-span ( or pier top) are decreased.

随着水的深度不断增加时，跨中（或墩顶）的最大位移、速度和加速度也逐渐减小。

However, the maximum displacement ratio for the eccentrically loaded short column is generally bigger than the ultimate strain of concentrically loaded short column.

在相同的长细比下，随着偏心率的增加，试件的承载能力降低，极限纵向变形率降低，但总体来说，偏压短柱的纵向变形率比轴压短柱的极限应变要大一些。

the results indicate that the maximum displacement increases, and the maximum dynamic stress decreases with depth.

结果表明，杆柱中的最大振动位移随深度增加量值逐渐增大，最大动应力随深度增加而逐渐减小。

while there are piles on both sides of the tunnel, the increment of maximum displacement is large, but the differential value is small.

两侧有桩时隧道整体下沉，最大位移增加量很大，但最大位移和最小位移差值较小。

for a system with a fundamental natural period in the long-period range, maximum displacement governs the seismic design.

对于长周期结构，地震最大位移反应是结构抗震设计的控制因素。

The experimental results of the tester maximum displacement range, resolution maximum load could meet the requirements.

实验结果验证了微力微位移测试仪的加载位移量程 、 分辨率、加载力等性能基本满足设计要求.

The Maximum displacement of nodes increases slowly with earthquake peak acceleration increasing, and the steel arch truss under the earthquake occurs strength failure finally. 2.

研究所得结论主要有以下几点：1、钢管拱桁架在地震作用下，最大节点位移随着地震加速度峰值增大缓慢增加，最终结构发生强度破坏。

: It is an important problem to indicate the maximum displacement coefficient ingear slotting tool design process.

确定最大变位系数是插齿刀设计的一个重要问题。而顶刃变尖是限制插齿刀最大变位系数的条件之一。

In the end, the effect of the maximum displacement was discussed, and the other salient feature relating with fictitious load are researched in the shape optimization.

本文最后讨论了最大位移量对形状优化的影响，对形状优化中的一些与虚荷载相关的特性也进行研究。

It shows that the relation between fractural orientation and percolating di-rection is of the maximum influences in the displacement effects;

指出裂缝方向与渗流方向的关系对驱替效果的影响最大；

Methods We introduce deviance residuals, weighted score residuals, likelihood displacement, maximum influence curvature and their plots.

方法介绍了剩余残差、加权Score残差、似然距离、最大影响曲率诊断量及相应的诊断图。

The optimum design of above problem was discussed where the maximum horizontal displacement of the earth-retaining pile wall was taken as the constraint condition, the interval of the soil anchors as variables and the minimum stiffness of the earth-retaining pile wall as the target function.

本文进一步以挡土桩最大水平位移为约束条件，以锚杆布置间距等作为变量，以挡土桩的最小刚度为目标函数进行优化。

By taking driven link angle displacement error minimum of limited positions and transmission angle maximum as optimizing objectives, mechanism dimension was distributed rationally so as to advanced the situation. And optimization was solved by genetic algorithms.

以从动件在极限位置时的输出角位移与理想角位移的误差平方和最小和四杆机构的最小传动角最大为双优化目标，合理搭配各构件的几何尺寸，并利用遗传算法求解优化问题。

the max lateral displacement increase with loading and the maximum position changes from deep under the slope toe to the middle of subgrade.

最大水平位移随着路堤荷载的增加，位置由坡脚下深处向路堤中间方向发展。

a maximum principle satisfied numerical method for compressible miscible displacement inporous media

求解多孔介质中可压缩混溶驱动问题的一类满足极大值原理的数值方法

The result shows that with the increment of excavation depth and the application of steel support, the deformation state of the retaining piles gradually develops form the anteverted curve towards foundation pit to bow curve and the place of Maximum horizontal displacement also move down.

监测结果表明：随着基坑开挖深度的增加和钢支撑的施加，围护桩的变形形态由向坑内的前倾型曲线逐渐变为弓形，最大水平位移发生的位置也随之下移。

The studies indicated that there was an exponential regression correlation among the displacement and stretching ratio of nerves and temporary cavity, the maximum of pressure peak ( MPP), and energy absorption ( EA).

实验表明，神经移位和神经牵拉率与瞬时空腔容积，压力峰值及能量吸收之间呈指数回归关系。

A Simple Method to Determine the Maximum Lateral Resistance and the Relative Displacement for Unbraced Multi-story Steel Frames

无侧向支撑多层钢框架最大侧向抗力及相应侧移值的一个简单算法

Through cutting tools' equivalent stress cloud picture and equivalent displacement map, get the maximum force position and maximum deformation. According to the theoretical analysis, prove the rationality of tool parameters selection, and provide process parameters and data support for the tool design.

通过对铣刨刀具的等效应力云图及刀具等效位移图，分析出刀具的最大受力位置及最大变形量，根据理论分析，证明刀具参数选取的合理性，为刀具设计提供工艺参数及数据支持。

Chief parts of the instrument consist of monolithic microcomputer and self-made dynamic magnetic grating sensor composed of magnetic head, magnetic scale, slide block and shell. It can display the time, displacement, speed in process, maximum and resilience speed, impact energy, etc.

测量仪主要由单片微机与自制动态磁栅式传感器（包括磁头、磁尺、滑块与壳体）组成，可测量运动过程的时间、位移量、速度与打击能量等。