metal joint的例句大全

The fine texture and microstructure of dissimilar metal joint was observed with microscope and shear strength of the joints was tested.

利用光学显微镜观察铜-钢异种金属堆敷接头的显微结构及显微组织构成。

Determination of method residual stresses in ceramic metal joint by X ray diffraction

陶瓷-金属连接应力X射线衍射测量方法

Effecting factors of cracking to dissimilar metal joint at cold bending

异种钢焊接接头冷弯开裂影响因素研究

Numerical Analysis of Stress Distribution of Adhesively Bonded Metal Joint under Cleavage Loading

劈裂载荷作用下金属胶接接头中应力分布的数值分析

Adding buffer layer of stress, designing reasonable stucture and adopting reasonable tecnology are the main methods to relax the residual stress in ceramic-metal joint.

而对残余应力的缓解主要采用加应力缓解层、设计合理的连接结构、采用合理的连接工艺等方法。

The micro analysis demonstrate that the cross section of FSW joint can be divided into weld nugget zone, thermal mechanically affected zone, heat affected zone and base metal.

通过对接头微观组织分析表明，接头横截面由焊核区、热机影响区、热影响区和母材区组成。

It is shown that the joint strength increases firstly and then decreases gradually with the increase of joining temperature, and the maximum value of strength is obtained at 850 ℃ because of the effect of ceramic-metal interfacial reaction and residual stress.

结果表明，由于陶瓷／钎料界面反应和界面残余应力的综合影响，随着钎焊温度的增加，接头强度先增加然后逐渐降低，850℃钎焊时接头强度最高。

The utility model relates to a thread tube bicycle frame made of carbon fibers combined with metal, which is composed of a plurality of supporting rods, an engaging head, and a two-way joint.

一种碳纤维与金属结合螺纹管式脚踏车架，车架是由数根支杆、衔接头及二通接头构成。

Discussion on Design of the Structural Attachment of Metal Bellows Expansion Joint

金属波纹管膨胀节某些构件设计问题讨论

Boundary and performance constraints were determined on the basis of the newest edition of Standard of Expansion Joint Manufactures Association of American EJMA-98 and National Standards of China GB/ T12777-1999, Metal Bellow Expansion Joint Common Technical Conditions.

以最新版的美国膨胀节制造商协会标准（EJMA-98）和GB／T12777-1999《金属波纹管膨胀节通用技术条件》作为设计依据，确定边界约束和性态约束条件；

Development of Quick Ball Joint of Aluminum Cast of Metal Pipes for Sprinkler Irrigation

喷灌金属管道球形铸铝快速接头的研制

Numerical analysis on stress distribution in single lap joint with a metal inlay

含镶嵌块单搭接接头应力分布的数值分析

Water-proof Joint Making for Vent on Metal-roof

金属屋面通风口防水节点制作

Therefore, the generation and development of the production skills of Zhangzi brass musical instruments are a joint achievement of social efforts such as advantageous geographical conditions, convenient transportations, mature metal smelting skills and excellent cultural atmosphere.

长子响铜乐器制作技艺的产生和发展是优越的地理条件、便捷的交通工具、成熟的金属冶炼技术和良好的文化环境等社会语境下，社会合力共同作用的结果。

Purification Study of Neodymium Metal by Zone Refining, Solid State Electrotransport and Zone Refining Electrotransport Joint Method

用区熔、电迁移和区熔-电迁移联合法提纯金属钕的研究

Investigation on the status of environmental pollution in a joint venture non-ferrous metal metallurgical enterprise

某合资有色金属冶炼企业作业环境污染情况调查

Effects of processing parameters on wettability of filler metal and temperature field characters of test plates during vacuum electron beam brazing ( VEBB) and microstructure of stainless steel joint brazed with BNi-2 filler metal are investigated in this paper.

探讨了真空电子束钎焊过程中电子束钎焊工艺参数对钎料润湿性和试板温度场的影响作用，以及BNi-2钎料钎焊不锈钢时的接头组织。

On quality control of plate flange joint construction in metal rectangle air ducts

金属矩形风管共板法兰连接施工质量控制

In this paper, the firm and imperishable joint between steel base and diamond grain was realized by using high-frequency induction brazing with the powdered brazing filler metal of alloy Ni-Cr, and by properly controlling the brazing current and time.

采用高频感应钎焊的方法，用Ni-Cr合金粉末做钎料，适当的控制钎焊电流和钎焊时间，实现了金刚石与钢基体的牢固焊接。

Tensile strength of back weld was higher than base metal, so back weld joint ruptured in the base metal in the experiment. The micrograph of fracture indicated that it was dimple fracture.

打底拉伸强度高于母材，接头断裂在母材处，焊缝断口呈韧窝型剪切断裂。