mm的例句大全

Character measurement of the plane target radiation on the 3 mm-band

3mm波段面目标辐射特性测量研究

Four patients were slightly limited in motion without influences on walking and working, while proper sports activities could be done, and the X-ray showed a displace of tarsometatarsal joint less than 2 mm.

足活动轻度受限，不影响行走、工作，可进行适当的体育活动，X射线片显示跗跖关节移位

Upper-tibia metaphysis lengthening was adopted at 1 mm/ d rate of distraction and iconography changes of knee joint were observed with X-ray, the morphologic changes of chondrocyte and cartilago articularis on tibial flat were observed with light and electric microscope.

采用胫骨上干骺端1mm/d速度缓慢牵伸延长。通过X线确定延长幅度及膝关节影像学变化，用光镜及电镜观察胫骨平台关节软骨组织及细胞形态变化，用扫描电镜观察软骨表面结构变化。

Debt Tax Shield Model under Revenue Uncertainty& Extension to MM's Tax Shield Model

收益不确定条件下债务税蔽模型&对MM税蔽模型的扩展

The elongation at break and tear resistance of the PLA/ PBAT 90/ 10 blend were 25% and 13.5 N/ mm, respectively.

PLA/PBAT90/10共混物的断裂伸长率为25%，撕裂强度为13.5N/mm。

The actual results show that system performance meets the technical requirements. Position error is less than ± 1 mm. Success probability of butt joint is more than 90 percent.

实际运行结果表明：系统综合性能指标符合工艺要求，定长裁断误差小于±1mm，对接成功率高于90%。

This article deals with the construction and sieving principle of the new-type Φ 200 mm standard test sieve shaker which is vibrated by the electromagnetic force and the elastic force.

介绍了一种新型电磁振动式Φ200mm标准筛振筛机的结构、工作原理。

Experiments comparing the measured value of ultrasonic thickness measurements and mechanical measurements on rough corroded materials without flattening the test surface were carried out. An average measurement error of from 0.6 mm to 2.2 mm was found in the ultrasonic measurements.

根据对未经平整的粗糙锈蚀表面分别进行超声波厚度测量和机械测量的比较试验，发现超声波测量的平均误差为0.6~2.2mm。

The test surface 2-D scanning system is realized by the movement of precision motorized stage, which is controlled by the computer through the microcontroller serial circuit. The minimal lateral movement distance is 0.039 μ m. The extended field will reach up to 12.5 mm × 12.5 mm.

单片机串口控制电路控制电控平移台的精确位移，实现了被测面的两维扫描，最小的横向位移为0.039μm，扩展后的视场达到12.5mm×12.5mm。

The weldability of 800 MPa high strength steel has been studied with 20 mm and 42 mm thickness plates by the maximum hardness test of heat-affected zone, Y slit cracking test and the test of weld energy input etc.

采用热影响区最高硬度试验、斜Y型坡口裂纹试验及焊接线能量的测试等手段研究了板厚分别为20mm及42mm的800MPa高强钢的焊接性。

Lateral bending test of the specimens was performed to examine the physiological overload using an Instron 5 500 universal material testing machine at the constant speed of 10 mm/ minute until fracture or dislocation was induced.

以侧弯方式进行超生理负荷试验，损伤试验在Instron5500型万能材料试验机上以10mm/min的速度匀速度加载，直至标本发生骨折或脱位而屈服。

ligule truncate, ca. 1 mm, margin ciliate.

叶舌削去，约1毫米，边缘具缘毛。

ligule entire, 5--7 mm, densely brownish pubescent;

叶舌全缘，5-7毫米，浓密带褐色短柔毛；

ligule ca. 0. 5 mm, scarious-membranous, apex truncate;

叶舌约0.5毫米，干膜质膜，先端截形；

ligule purple, ca. 1 mm, fimbriate at top;

叶舌紫色，约1毫米，流苏状的在顶端；

ligule arched, ca. 1 mm, ciliate;

叶舌拱起，约1毫米，纤毛；

The upper 2 expanding leaves of tube seedlings, cut into 4 mm X 4 mm and inoculated with abaxial layer downside may have the greatest regeneration efficiency. This variation was shown in the stage when the leaves were expanding.

组培苗顶端前2节位展开叶片，切成4mm×4mm左右，远轴面接触培养基时的再生效果最好。这种变化主要表现在叶片全展前后，到叶片发育后期则接近野生型。

Its tectonic geomorphology is characterized by clear linear fault scarps, the average vertical slip rate of the fault is about 0.41 ± 0.27 mm/ a since late period of the late Pleistocene.

断裂在地貌上表现为明显的挤压逆冲断层陡坎，晚更新世晚期以来的平均垂直滑动速率为0.41±0.27mm/a。

When hanging glue roller chain festival and crouching for 100 mm, hang teeth of a cogwheel in entrance of glue was 5.The transmission adopted the way pneumatically.

当挂胶链条节踞为100mm时，入胶口挂轮齿数为5；传动系统采用气动步进方式；

Results It took 2~ 6 months to close the teeth space, the teeth moved 1.6 mm every month, 12~ 20 months later, wore keeper for 1 years, then got better effect.

结果15例牙列拥挤患者在拔牙后，关闭拔牙间隙一般2～6个月完成，平均每个月牙齿移动1.6mm；矫治12～20个月，再佩戴保持器1年，均获较好效果。