model element的例句大全

The author also made a static and dynamic test for the semitrailer tractor in order to provide practical basis for the finite element analysis. And the test can also verify the correctness of the finite element model.

并对该牵引车进行了静、动态电测试验，为有限元分析提供实践依据，并验证了有限元模型的正确性。

According to the characteristic of the structure, working type, technical parameters and the load characteristics, a finite element analysis model is established.

根据天线结构的构成特点、工作方式和技术参数、载荷特征，合理地建立了天线结构的有限元模型，并制定了计算工况。

Formulation of Hybrid Model Triangular Element of Thin Shells by Tensor Analysis

用张量分析进行薄壳混杂模型三角形单元的构式

This is called supersensitive transitions. Based on the irreducible tensor operator method, a computation model and corresponding computer program for calculating the hypersensitive transition spectrum of f-element were developed.

以不可约张量算符方法为基础建立了计算f元素超灵敏跃迁光谱的数学模型并编制了相应的计算机程序。

In this paper, based on the tentative design of design department, using space beam element and plate and shell element, the finite element model of aqueduct is built. Aqueduct of Ming-he in the middle of the engineering is analyzed by ANSYS finite element program.

根据设计部门提供的设计方案，本文采用空间梁单元、板壳单元建立渡槽结构的有限元模型，利用ANSYS程序，对南水北调中线工程的洺河渡槽进行分析研究。

Solid model is made for mudsill and bracket using I-DEAS, and finite element static analysis is carried out, on the base of terminal conditions setting for the overall structure and defined restrain.

利用I-DEAS软件建立了底梁及支架的实体模型，基于整体结构设定边界条件，定义约束，进行了有限元静力分析计算。

Finite element model of Prestressed concrete beam was created according to the kinematic model of beam compression bar, then the frequencies and modals of test beam were calculated by it.

论文中按照梁式压杆两端承受压力的动力模型建立了预应力混凝土梁的有限元计算模型，进行了试验梁的频率和振型的计算。

Based on the theory of finite element analysis, combining engineering practice, using the bridge structural analysis software, establish the finite element model of the extradosed cable-stayed bridge, compared the static load test check the model.

在斜拉桥结构分析理论基础上，以实桥为工程背景，运用桥梁结构分析软件，建立矮塔斜拉桥空间有限元模型，以静力荷载试验为对比校核模型。

Updating design parameters of finite element model by using test complex modal data

基于实验复模态参数的有限元模型修正

Comparing test mode result with simulation mode analysis data, the finite element model is verified.

通过试验模态结果与模态仿真分析数据的对比，验证了有限元模型。

At the same time the paper establishes the solid finite element model of T-beam, and analyses the fatigue cracks, and the time-stress history of the reinforcement in tensile region and of the concrete in compressive zone under automobile load spectrum.

同时建立了T型梁有限元实体模型，分析了车辆荷载谱作用下梁的疲劳开裂、压区混凝土以及拉区钢筋的应力时间历程等问题。

First, establish finite element model, make reasonable arrangements for model size, tensile region heighten, restricted location.

首先，建立起有限元模型，对各种模型中的尺寸、受拉区高度、约束位置进行合理的布置。

The results of finite element model and theoretical formula are proved to be in good agreement with the experimental data.

把有限元模型和建议公式的计算结果与试验结果进行比较，三者吻合良好。

Finite Element Simulation of Cylinder Necking by Using a Damage Model Necking of a round tensile bar

圆柱杆材料损伤模型的计算机模拟光滑圆柱拉伸试件的颈缩分析

A thermal elastoplastic contact model which can take into account the effects of temperature-dependent yield strength was developed by using finite element method.

应用有限元方法建立了可考虑屈服应力温度相关效应的粗糙表面热弹塑性接触模型。

Finite Element Model Theoretical Analysis of Dry Type Gasholder Sealed with Rubberized Fabric

柔膜密封干式储气罐的有限元理论分析

Finite element program of non-linear analysis to pile is made and together with results of building test pile and model test pile, therefore, the feature of load transferring and deformation mechanism were deeply analyzed.

对工程试桩的静载试验结果进行分析，确定单桩极限承载力。室外模型桩试验通过在桩身埋设测试元件，研究水泥土组合桩荷载传递规律以及变形特性。

Research methods: This paper analyzes the skew frame with 2D rigid frame and 3D space model of thick plate element with MIDAS Civil structure design system, and their results have been contrasted with comparison method.

研究方法：运用MIDAS有限元分析软件，分别建立厚板单元的三维空间模型和平面刚架的二维平面模型对某斜交框架桥进行分析，并采用对比法对2种模型结果进行对比。

Research results: The analysis process of frame bridge with skew angle has been given by use of MIDAS. We obtained the outcomes from two models and the difference between results with 2D rigid frame and 3D space model of thick plate element.

研究结果：给出了用MIDAS分析斜交框架桥的详细分析过程，得出斜交框架桥三维空间模型和二维平面模型分析的结果，并得出2种模型计算结果的差别。

The finite element model has been built by the study of the influence of element distribution in crack district, axial direction, annular direction and the thickness of the pipe.

研究了管轴向、管环向、管壁的单元分布的影响，建立了三通有限元模型，最终的有限元模型既能满足精度要求又能节省计算时间。