model element的例句大全

Establishment and analysis of three-dimensional finite element model based on tail-suspended rat experiment

基于大鼠尾部悬吊实验的三维有限元模型建立与分析

Three-Dimensional Finite Element Model for Relationship between Wellbore Failure and Mud Density

井眼破坏与钻井液密度关系的三维有限元模型

The vibration simulation model of a transducer system in thermosonic wire bonding was established by finite element method and verified by electrical sine sweeping exciting experiment.

在建立热超声引线键合换能系统各子部分运动方程的基础上，利用有限元方法建立空载情况下换能系统的振动特性仿真模型，并采用正弦扫频方法验证仿真模型。

Taking into account temperature-dependent thermal conduction and heat capacity, a three-dimensional transient thermal finite element model has been developed.

在考虑随温度变化而变化的热传导、比热容等热物性参数的作用下，建立直接金属多道烧结的三维温度场有限元模型。

An analysis method of the thermohydrodynamic model of finite circular journal bearing which is defined by analysis formula in the axial direction and distributed by finite element in the circumferential direction was presented.

提出了对轴向解析、周向有限元压力分布的有限宽圆轴承模型进行流体动力润滑热效应分析的方法。

Finite element method and ultrafast thermoelasticity model are combined to simulate the microbump formation irradiated by a femtosecond laser.

本文结合有限元方法和超快热弹性模型对飞秒激光辐射下形成的微突起结构进行了数值模拟研究。

Finite element analysis of head/ disk continuous sliding contact was performed to investigate temperature field and thermal stress field due to frictional heat using an axisymmetric thermal model. Characteristic temperature rise with sufficient sliding time was exhibited.

采用二维轴对称有限元模型计算磁头/磁盘滑动接触下，铝质磁盘的稳态温度和热应力场以及热退磁临界条件。

The stress-strain state for notched specimens subjected to constant amplitude proportional multiaxial loadings was also calculated and analyzed by the finite element model and the theoretical stress concentration factor of the notched specimens had obtained.

针对多轴比例加载的情况，利用弹塑性有限元法对缺口件在拉&扭复杂加载下的应力应变场进行了计算和分析，得到了缺口件的应力集中系数。

Based on the dynamic analysis of the three-dimensions finite element model of Three-Gorges ship lift structure, the equivalent reduced mechanical model is established.

本文基于三维有限元模型的动力分析建立了等效的简化力学模型。

The finite element computation method was used to establish a three-dimensions limited mathematics model for a complex structure system with two different metal compositions.

用有限元计算法，通过对各单元的分布和整个求解区域的总和，建立了两种不同金属组成复杂结构体系的三维有限元数学模型。

The relaxations of stress of PTT fibre and PET fibre may be simulated by using a three-element mechanical model.

三元件模型能较好地模拟PTT纤维和PET纤维的应力松弛过程。

At last, the fundamental viscoelastic parameters are calculated according to the data of the electrostatic experiment and a three-element solid inversion model.

同时建立了三元件固体反演模型，依据静压试验数据，对橡胶的基本粘弹性参数进行反演。

Through coupling the pedestal and the reflector together, this paper presents a FEM model, then the static and dynamic finite element analysis of the whole antenna structure was made under multiple loading conditions.

将座架和反射体进行耦合，建立了有限元分析模型，在此基础上对耦合的整体结构进行了多工况静力、动力分析。

With the finite element analysis techniques the finite element model of the flat-panel is attained, and the model of the main structure of the damping system is built.

利用有限元分析技术得到了平板有限元模型，继而建立了减振系统的主结构模型。

By utilizing I-deas software, the finite element model of the main structure of Car Dumper is established and through static analyzing to the definite element, the static analysis results at different rotating angles under corresponding operation cases are obtained.

利用I-deas软件建立了翻车机主结构的有限元模型，对其进行有限元静力学分析，得到了相应工况下不同翻转角度状态的静力分析结果。

Dynamic and static characteristic of the main system is the key factor of production. So it required to establish accurate element model.

对这种产品，主结构系统的静动态品质是影响产品性能的关键因素，这就要求建立准确的有限元模型。

In this paper, taking large diameter diaphragm wall as an object, plane and space finite element model of circular diaphragm walls which have or not have ring BEAM were established, by using ANSYS software pre-processing module.

本文以大直径的圆形地下连续墙为研究对象，利用ANSYS软件的前处理模块，建立了带环梁和无环梁两类大直形圆形地下连续墙的平面和空间有限元模型。

According to the wall testing process, we put finite element numerical simulation on the cavity wall which is set the ring beam but without structural concrete column, using discrete model to analysis the principal stress, cracks distribution and displacement of the wall.

参照墙体试验过程，对设置圈梁但无混凝土构造柱的空斗墙体进行有限元数值模拟，采用分离式模型对墙体的主应力、裂缝分布与墙顶位移变化进行分析。

Finite element model to analyze cylinder-cylinder intersection under crosswise thrust load

柱壳接管受横向推力应力分析的有限元模型

For the purpose of control vibration on real time, dynamic condensation method is adopted to reduce the finite element model of a certain platform. The displacement responses of the two models under the environmental loadings agree with each other well.

采用动力减缩技术，得到适于振动控制研究的平台减缩模态，在随机环境载荷激励下，减缩模型与有限元模型两者位移响应具有较好一致性。