model element的例句大全

With the help of simplified double coil unit model, finite element simulations of the mutual inductance between eddy current array sensor coil units are implemented, and the elimination methods of mutual inductance are discussed.

借助双线圈单元简化模型，进行了涡流阵列传感器线圈单元间互感干扰的有限元仿真，得到了抑制互感干扰的方法。

Finite-Element Model for the Thermal Analysis of Large Main Truss of Space Station'Solar-Array

大型空间桁架结构热分析的有限元方法

A Study of Transient Thermal Circuit Model for the Cable Transformer Coil Based on Finite Element Method

基于有限元法的电缆变压器绕组的暂态热路模型研究

The finite element method ( FEM) software ANSYS is employed to model device and simulate thermal distribution so as to obtain temperature improvement.

利用有限元软件ANSYS对器件进行建模和三维热模拟，研究器件温度分布的改善情况。

Based on the theories of gear engagement, contact analysis, friction and heat transfer, a model and method of finite element structure and thermal analysis for the drive were established.

基于齿轮啮合原理、轮齿接触分析、摩擦学和传热学，并将有限元方法、理论分析计算以及实验测量数据相结合，建立了塑料蜗轮与钢制蜗杆传动轮齿结构和温度分析的模型与方法；

The paper use finite element analysis method analysis the thermal impact of PCBA during the reflow soldering, and building the temperature and stress distribution model.

本文利用有限元法对PCB组件在再流焊过程中的受热进行分析，建立瞬态温度场和应力场模型。

Simulative analysis on thermal load of piston based on parameterized finite element model

基于参数化有限元模型的活塞热负荷仿真分析

The long-term heat calculation of the thermal model has been done by using finite element analysis software-ANSYS.

该模型综合考虑了热辐射、热传导和材料物理性能随温度变化的特点，并利用有限元软件ANSYS对简化热模型进行了长期发热计算。

A mathematical model for determining the thermal influence zone of buried hot oil pipeline was developed and solved numerically by the finite element method.

建立了埋地热油管道热力影响区的数学模型，并用有限元法进行了求解。

Three-dimension model on thermal-stress coupling analysis is performed according to the material features and working environment of the cooling pipe in Zn liquid, using the large-scale finite element analysis software ANSYS.

针对锌液冷却管材料特性和工作环境，利用ANSYS有限元分析软件建立了冷却管的温度应力耦合分析的三维有限元模型。

Aimed at the fibre reinforced composite material barrel, the coupled thermo-mechanical analysis model was developed and solved by using finite element method.

以纤维增强复合材料身管为研究对象，采用有限元方法，建立复合材料身管热结构耦合分析模型并进行了求解；

Two parameters of the crack dynamic propagation driving force, energy release rate and crack tip opening angle, are calculated by establishing a finite element model of the crack dynamic propagation in gas pipelines and considering the attenuation of the crack propagation velocity.

通过建立输气管道裂纹动态扩展的有限元模型，并在模拟计算中考虑裂纹扩展速度的衰减，分别计算了表征动态裂纹扩展驱动力的两项参数&能量释放率和裂纹尖端张开角；

The Collapsing Strength Finite Element Computation Model of Slotted Liner

割缝防砂筛管抗挤强度有限元计算模型

A nonlinear FEM analysis model is set up based on the finite element analysis software& ANSYS. The staggered shear wall structure and the coupled shear wall structure are analyzed with this model.

通过建立非线性有限元分析模型，运用通用有限元分析软件ANSYS对新型隔层错跨钢筋混凝土剪力墙结构和传统双肢剪力墙结构进行对比分析。

The papers whose research object is a 14-floor frame-supported shear wall. By establish a 3-dimension finite element model and use the analysis soft-ANSYS, make the study focus on the static analysis.

本文以一幢14层的框支剪力墙结构为研究对象，通过建立三维有限元分析模型，运用大型有限元分析软件ANSYS对结构进行静力分析。

Drawing Realistic 3-D Graph by Means of the Data of Finite Element Model

利用有限元模型数据绘制真实感三维图形

Concerning of the interactions both between wheel-rail and linear induction motor ( LIM)-reaction plate ( RP) of this system, the vehicle-track vertical dynamic model is built based on coupling dynamics and dynamic finite element method.

本文基于动力有限元和耦合振动理论，考虑轮轨关系以及直线感应电机和反力板之间的相互作用，建立了直线电机地铁系统车辆轨道垂向动力学模型。

The paper concerning finite element analysis and study on beam under vibration equipment, through which the finite analysis module is set up. Based on model reasonableness analysis, the method which effectively controls dynamic reaction of structure system is studied.

对选煤厂动力设备下梁进行了有限元分析研究，建立了梁的有限元分析模，分析了模型的合理性，探讨了控制结构体系动力反应的有效方法。

The reactivity effects were compared between unit mass nuclear waste element MA and uranium element on the fast neutron reactor model by simulating calculation.

在快中子反应堆模型上，用MC方法模拟计算和比较单位质量MA核素和易裂变核素引起的反应性变化。

The utility model relates to the field of nuclear fuel components, in particular to an upper tube seat of a pressure water reactor fuel element.

本实用新型涉及核燃料元件领域，具体涉及一种压水堆燃料组件上管座。