oblique plane的例句大全

Mohr's circle is required for any oblique plane passing through the point O.

需要对通过点O的任意斜截面绘制莫尔图.

Discussion about the Friction Force does Work When the Cylinder does Pure Roll along an Oblique Plane

圆柱沿斜面作纯滚动时摩擦力作功的讨论

On the oblique plane parallel to the horizon segment, the intratemporal facial nerve was completely disclosed.

与水平段平行的斜平面可显示颞骨内面神经.

The parts design and principle were discussed that includes the oblique plane, the swing arm parallelogram, and the end plane cam.

阐明斜平面、摆臂平行四边形、端面凸轮等部分的设计和原理。

Landslide with plane rotation under lockup of centric segment is formed in the course of progressive failure of layered rocks on the oblique bank slope.

中部砥柱锁固平面旋转滑坡，是切向层状岩质斜坡在特殊的边界条件控制下，发生渐进性变形而形成的。

As the film sample is fixed on one plane by tighten bolt, this device can realize the deflection of optical path. And the reflectivity of the sample is measured by using oblique incident ray.

使用该装置并通过平面和样品背后的顶丝固定薄膜样品的安装方式，可实现光路转折，完成斜入射光对薄膜样品反射率的测量。

this oblique configuration redistributes the shock waves that pile up in front of a plane at mach speeds and cause drag.

这种倾斜的外形把超音速飞行时集中在飞机前部并形成阻力的冲击波重新分布。

stage projection; oblique projection on plane screens, drawings and nomograms for use in practice

幻灯片和电影片的舞台和剧场放映.平面银幕上的倾斜放映.实际应用的工作资料

design of digital image plane of high-speed rotating mirror camera with oblique incidence

斜入射高速转镜相机数字像面的研究

among all parameters, pin insertion angle, pin diameter and pin density are primary for compression and shear properties, while the oblique angle and pin layout could be neglected except that pins on transverse plane about shearing load have little contribution to the shear behavior.

Pin植入角、直径以及植入密度是压缩和剪切性能的主要影响因素，而端部斜切角及空间布局的影响可忽略。此外，横向面内pin对剪切性能的贡献较小。

This article embarks on a concrete question , elaborates the essential distinguishes between oblique and plane bending.

在总结内力作图方法的基础上,推导了作平面弯曲梁内力图的一种快速作图法——面积法.

A New Method for Calculation Shear Plane Area in Oblique Cutting with Double Edge

新的斜角非自由切削剪切面积计算方法

The paper proposes a new method for calculating shear plane area based upon a new oblique cutting model with double edge.

根据新的斜角非自由切削模型，本文提出了新的剪切面积计算方法。

The relationship between the oblique line and every projection plane included angle, and It's application on problems proposed and solved were discussed in the paper.

本文论述了一般位置直线与各投影面的夹角相互关系问题及其在命题、解题方面的应用。

The investigation of the distribution of stress inside a cutting tool in the chip flow plane during oblique cutting ( II) tilting position

斜角切削切削刀具流屑平面内应力分布的实验研究（Ⅱ）倾斜角（转炉），倾斜位置

The projection curve analysis when a plane cuts off a circular cone with an ellipse section line at an oblique angle

平面斜截正圆锥截交线为椭圆时投影曲线分析

The common method for obtaining the angle of the plane figure to projection plane is through the right-angled triangle method after getting the double-face projection of the plane figure on the basis of the conception of maximum oblique line.

求平面图形对投影面的倾角，通常需要知道平面图形的两面投影，利用最大斜度线的概念，通过直角三角形法求得。

Dynamics and stability criterion of oblique layered landslide with plane rotation under lockup of centric segment

中部砥柱锁固平面旋转切向层状岩质滑坡启动力学机理与稳定性判据

Dynamics and stability criterion of oblique LAYERED ROCKY landslide under lockup with combination of flank and bedding plane

侧翼与滑床复合锁固切向层状岩质滑坡动力学机理与稳定性判据