pawl的例句大全

Analyzing the reasons of spring failure on pressing pawl of cutting machine and heat treatment

剪板机压料爪子弹簧失效原因分析及处理

Design characteristics of pawl pole permanent synchronous machine

爪极永磁同步电机的设计特点

Simulation and Analysis of a Two-raking Pawl Loading Mechanism

双耙爪式装载机构的模拟分析

The working principle of conveyer, sorts, working manner and application range of brake and pawl are introduced.

介绍了带式输送机的工作原理、制动器与逆止器的种类、工作方式以及使用范围。重点指出了：①向上输送的皮带机在倾角小于5°时可不加制动器和逆止器；

This paper introduces the structure and design characteristics of pawl pole permanent synchronous machine, and illustrates the relations among main structure sizes.

介绍爪极永磁同步电机转子的结构及设计特点，并说明了一些主要结构尺寸间的关系。

Improvement Design of the Borer of 7523 type, 540A type Truck Brake Pulley and Retaining Pawl

7523型、540A型汽车制动鼓蹄镗削机床的改进设计

A bracket will be installed within the transmissions to assure that the park pawl shaft remains properly in position.

在变速器内安装保持架来确保驻车止动爪定位销处在正常位置。

A two-raking pawl mechanism is a kind of loading one used in a roadheader; its performance and property are unknown now.

双耙爪是在掘进机上使用的一种装载机构，其性能和特征目前还不甚清楚。

The paper introduces the design performance of 7523 type, 540A type truck brake pulley and retaining pawl, and puts forward improving way for some constructive defects in a borer.

介绍了7523型、540A汽车制动鼓蹄镗削机床的设计性能，提出了机床部分结构缺陷的改进办法。

This control effect can be got by designing the size of pokedwheel, using the self locking character of worm wheel and worm pole and connecting the pawl mechanism with overtravel limit switch.

通过有效设计拨轮的尺寸，利用蜗轮蜗杆的自锁特性，将棘轮机构与行程开关联为一体，达到自动输球控制的目的。

The pawl type bamboo roots grab was designed.

竹爪式竹根挖掘机方案设计。

The virtual prototype of the clutch is built based on Pro/ E and the switch process of the SSS clutch is simulated by MSC Adams. The simulation of the impact performance of the pawl and pawl wheel and the engaging performance of the middle part is finished.

利用Pro/E及MSC ADAMS建立该离合器的虚拟样机模型，并在MSC ADAMS中对离合器动态接合过程进行仿真，分析棘轮棘爪的碰撞特性，以及中间件的啮合特性。

The fine blanking dies of the pawl and the chute used for the seat recliner were firstly introduced in this thesis, and failure analysis has been carried out in view of mechanical calculation, metallographic test, hardness test and SEM.

本文首先针对棘爪、滑槽板两副精冲模具出现断裂的凸模，从力学强度校核、金相试验、硬度试验、断口电镜扫描等进行试验分析。

Ratchet mechanism is often used in the reducer of the casting crane. This paper uses Pro/ ENGINEER software to create the ratchet mechanism and simulate its running and studies the stress and deformation of the ratchet wheel pawl by Pro/ MECHANICA.

针对铸造起重机用减速器常采用的棘轮装置，采用三维实体造型软件Pro/ENGINEER建立其实体模进行运动仿真，利用Pro/MECHANICA有限元分析模块对棘爪进行应力、应变分析，得到棘爪需加强的部分。

Heavy hammer on the pawl through the release of the lock device on Spindle lock spindles;

重锤上的棘爪通过释放装置上的锁锭轴锁锭；

The blades are positioned on the large handle by a rotating shaft screw, and the pushing pawl and a pawl torsion spring are connected with the small handle through the pawl pin.

小手柄上通过棘爪销柱连接有推进棘爪及棘爪扭簧，推进棘爪受到棘爪扭簧的压力始终压制在刀片的齿上；

This paper deels with the filling density calculation and design methods to determine the num-bers of the pawl and teeth of the ratchet wheel as well as linkage lengths of the mechanism.

本文对该机构的纬密计算，棘爪数、棘轮齿数以及传动连轩长度的确定等设计方法均作了较为详细的介绍。

Tyre-lock chain interlocking pawl ( winding) wheel

胎锁链（轮胎防滑）大钢轮，互锁棘爪轮

The feasibility for rolling special section pawl steel with the existing& 180 mm mill at laboratory has been discussed.

研究了用180mm轧机轧制异型断面棘爪钢的可行性。

The fastening tool further includes a coil feeder ( 720) assembly having an indexing pawl ( 722).

紧固工具还包括具有分度棘爪的卷料进给组件。