pin contact的例句大全

Note that die length of ejector pin contact with the mould plate is kept to a minimum by incorporating a clearance diameter hole in the mould plate.

注意，顶杆和模板的接触长度通过在模板中加工一个放大直径的孔来保持最小。

Then, contact stress and deformation of a half sphere micro-convex was simulated and calculated by using finite element analysis software ( ANSYS), and the testing model of pin-on-disc sliding wear was proofed through test data.

采用有限元分析软件ANSYS对半球形微凸体接触应力和变形进行了仿真计算，并用销盘滑动磨损试验数据给予验证，证明了所建立的仿真模型是可行的。

The process of interference-fit between swage-locking pin and composite laminate has been analyzed by introducing the static state contact arithmetic.

在分析过程中采用静态接触算法模拟环槽铆钉与复合材料板的干涉配合过程。

Dust can easily lead to poor contact socket and board, In addition, some cards on the motherboard, the form of chip pins, and is often due to oxidation and poor contact pin.

灰尘很容易引发插槽与板卡接触不良，另外，主板上一些插卡、芯片采用插脚形式，也常会因为引脚氧化而接触不良。

The two-dimensional and three-dimensional contact stress simulation analysis of the pin on disc contact couple were carried by the ANSYS software.

利用ANSYS软件分别对销盘接触副进行二维和三维的接触应力模拟分析。

The numerical value and conformation of the contact stress field arised great changes when the contact of Pin on disk was changed from static to dynamic state.

销盘接触由静态变为动态时，接触应力场在形态和数值上都发生很大变化。

and the third contact pin is connected with a sheltered ground.

所述第三插针连接保护地。

embedding the ceramic contact pin at the end of the metal sleeve piece to form a component;

再将所得的陶瓷插针嵌设在所述金属套筒的一端以形成组件；

Stress simulation has the function of calculating any required stress values of contact area drawing the graph of stress distributing trend under the contact surface, and simulating the distributing condition of contact stress of Pin-on-Disc using the style of nephogram.

其中，应力仿真模块具有计算接触区任何需要的应力值功能，并可模拟出接触面下的应力分布趋势曲线图，采用云图方式仿真出销盘的接触应力分布情况；

The results show that there are the continuous deformation contact phenomena and heterogeneous wear phenomena between the axle box with axle pin of the clearance joint, these phenomena make the amounts of dynamic wear larger where the continuous deformation contact occurs.

计算结果表明副元素间呈现出连续弹性变形现象，在连续变形接触处，动态磨损量较大使磨损加剧，并出现非均匀磨损。

Sleeve joint secures more than a pin joint, it's surface contact with the rim's inner wall is increased yet we're able to maintain it's lightweight properties.

袖套连接比销钉连接更加安全，可靠。这种表面与轮圈内部墙的接触更加增加了我们能维持它的轻量的特性。

Software I DEAS and MARC were used to calculate the thread face contact stress during the make up process, and to analyze the effect of taper mutation of pipe ( pin thread) and coupling ( box thread) on the thread face contact stress quantitatively.

利用I－DEAS和MARC软件计算了拧接过程螺纹齿面的接触应力，定量分析了管体（公螺纹）和管接箍（母螺纹）的锥度变化对齿面接触应力的影响。