plastic strength的例句大全

Effect factors and increasing law of plastic strength ( P s) of clay hardening grouts

粘土固化浆液塑性强度增长规律及其影响因素

In chapter 2, according to the theory of strength of steel wire and plastic along with the result of hydraulic pressure burst test and short-term hydraulic pressure strength test, we calculated the strength of steel framed polyethylene plastic pipe and determined the principial working pressure.

第二章是根据传统的钢丝和塑料的强度理论以及静液压爆破试验、短期静液压强度试验结果，对钢骨架塑料复合管进行强度计算及工作压力的初步确定。

During the deformation, disintegration and failure of debris-soil landslides, in space the plastic strain of the sliding mass and shear strength of the rock or soil mass on a sliding plane are different.

在碎石土滑坡变形解体破坏过程中，在空间上滑体塑性应变和滑面上岩土体抗剪强度的发挥程度是不一致的；

According to the residual strength of casings after tubercular corrosion, with elastic-plastic finite element method, the changes of collapse resistance, burst strength, and tensile resistance of casings are analyzed.

为此，文章建立CO2点蚀模型，以点蚀后套管的剩余强度为出发点，应用弹塑性有限元方法分析了点蚀套管的抗挤强度、抗内压强度、抗拉强度的变化。

After annealing, the tensile strength of sample hot-dipped with Al-7% Si, improved remarkably, and the plastic deformation increase at the same time.

浸Al-7%Si退火后抗拉强度有显著提高，塑性也有所改善。

Test method for interlaminar tensile strength of glass fiber reinforced plastic laminates

GB/T4944-1996玻璃纤维增强塑料层合板层间拉伸强度试验方法

The specific strength of RS/ PM Mg_ ( 97) Zn_1Y_2 is the highest among all metallic alloys and the RS/ PM Mg-Zn-Y alloys have the best combination of tensile yield strength and plastic elongation among all kinds of Mg-based alloys.

在所有的金属合金中，RS/PM Mg97Zn1Y2合金的比强度是最高的。而在所有的Mg基合金中，RS/PM Mg-Zn-Y合金具有最佳的综合性能。

The results show the tensile strength, yield strength, hardness and elongation increased obviously due to the decreasing of the grain size of pure Cu after severe plastic deformation.

研究结果表明：经过大变形后，由于纯铜的晶粒得以细化，抗拉强度、屈服强度、硬度和断裂延伸率都显著增加。

Investigation of Strength Test of Unidirectional Glass Fiber reinforced Plastic Rods

单向玻璃纤维增强塑料杆材强度测试研究

Coulomb yield-law is used to determine elastic and plastic limiting load of thick cylinder and thick sphere in strength-differential material.

本文利用库仑屈服准则，研究了拉压异性材料厚壁圆筒和厚壁球壳的弹性极限载荷和塑性极限载荷，得出了新的结果和结论。

Elastic-plastic crack growth in the cracked thin sheet of high-strength material

高强薄壁裂纹体的弹塑性裂纹扩展

Due to their high strength, good fatigue strength and corrosion resistance, more and more difficult-to-cut material such as carbon fiber reinforced plastic ( CFRP), titanium alloy and aluminum alloy are used in large components in aerospace industry.

碳纤维增强复合材料、钛合金和铝合金等材料因具有高强度、良好的抗疲劳性和耐蚀性等优点，已广泛应用于航空航天领域。

It is found that particle and substrate preheating can promote the occurrence of thermal softening effect, and then enhance the plastic deformation and final bonding strength between particles and substrate.

研究结果表明，预热处理可以促进粒子或基体发生热软化效应，进而促进强塑性变形的发生，同时提高接触面附近的局部温度，促进粒子与基体的结合。

Study on Production Technology of Resin Paper Overlaid Bamboo Composite Board Manufacturing technology and applicable feature of the high strength plastic-coated ply-bamboo

覆塑竹碎料板生产工艺研究覆塑高强竹帘胶合板的制造工艺及使用特性

The main behaviors of this kind low temperature steel are that it can keep enough strength, plastic and impact-resistant under low temperature.

低温钢重要的特性是在低温工作条件有足够的强度、塑性、耐低温冲击。

When using the 3D elastic-plastic contact FEM strength reduction method to compute the stability coefficient of debris-soil landslides, the space effect of the sliding mass may be considered in order the calculation results to be more accurate.

研究结果表明，采用三维弹塑性接触有限元强度折减法计算碎石土滑坡的稳定性系数，可以考虑滑坡体的空间效应，使计算结果更加精确；

Solutions of some plastic plain strain problems based on unified strength theory and unified slip line field theory

用统一强度理论和统一滑移线场理论求解某些塑性平面应变问题

At absolute zero temperature, the strain rate only effect the plastic deformation, the yield strength increased with the increase of strain rate.

在绝对零度下，应变率对应力曲线的弹性变形阶段没有影响，而只影响塑性变形阶段。

The research shows that the plastic blind drain is of good performance in water collecting, drainage, compressive strength, and endurance.

初步研究结果表明：塑料盲沟具有较好的集水、排水、抗压性能和耐久性。

Design of measurement and control system of an intelligent plastic impact strength tester

智能化塑料冲击韧性试验机测控系统设计