plastic zone的例句大全

In order to predict the mixed mode crack growth in sliding mode fracture, the fracture criterion of mixed mode crack growth is introduced here based on the maximum size of plastic zone near crack tip.

为了预测复合型裂纹呈滑移型（Ⅱ型）的断裂，在此提出了复合型裂纹扩展的最大塑性区尺寸断裂判据。

The effects of the slip plane orientation and load on dislocation emission or plastic zone have been investigated.

考察了滑移面取向、外荷对发射位错及塑性区的影响。

The result also reveals that the reinforcement material penetrating into the plastic zone of the slope will effectively elevate the slip resistance effect.

同时，计算分析了加筋材料摆放位置不同时，对土坡抗滑能力的影响效果。提出当将加筋材料贯穿于土中塑性区时，加筋效果最明显。

However, in the rain condition, the slope displacement is large, plastic zone extends to the foot of the slope, the stability coefficient is decrease.

而在暴雨状态下，边坡发生较大位移，塑性区延伸至坡脚处，稳定性下降。

In this paper, with Mises yield criterion, the plastic zone distribution in front of crack tip with mixed mode(ⅰ ⅱ) loading is analyzed theoretically.

利用Mises屈服准则从理论上分析了Ⅰ－Ⅱ复合型裂纹尖端前缘的塑性区分布。

Using strange element, Shih obtained plastic zone shape at the crack tip for mixed mode crack.

Shih〔1〕应用奇异单元，获得了不考虑应力松驰小范围屈服条件下复合型裂纹尖端塑性区形状。

The Sliding Displacement and Plastic Zone of Mode ⅱ Dynamic Crack Tip

Ⅱ型动态裂纹尖端的滑开位移及塑性区

In this paper, the secondary stress, radius and displacement in plastic zone of cylinder tunnel under 3-D stress are analyzed on basis of do u ble shear strength theory.

为此本文利用双剪强度理论分析了三维应力状态下圆筒形巷道塑性区次生应力、半径和位移。

The strength reduction FEM, taking the run-through of plastic zone as unstability criterion, can obtain actual stress distribution and simulate the process of slope failure.

以塑性区贯通为失稳判据的强度折减有限元法，可以很好的求解真实的应力分布和模拟软土边坡破坏过程，是一种值得提倡的方法。

The effect of cyclic loading makes the plastic zone hardening ( or softening), which raises the stress level in Dislocation-Free Zone ( DFZ) and the value of-integral, and may lead to fracture.

循环载荷使得裂纹尖端的塑性区循环硬化/软化，这使无位错区的应力和裂纹尖端区域的J积分的值升高，从而有可能导致开裂。

Stress Analysis of Plastic Zone of Wheel Groove for Continuous Extrusion by Successive Element method

连续挤压轮槽塑变区应力分析中的逐次单元法

In model 2, the material parameters are independent of the plastic volumetric strain but is related to the temperature change that causes thermal softening, the model is used inside the fault zone.

模型2用来模拟断层物质，其强度只同热状态有关而与塑性变形无关。

The model conforms better tol the practice than the ring models due to considering the effect of the plastic bending of the longitudinal transition zone.

由于考虑了纵向过渡段塑性弯曲的影响，作者提出的模型较以往的环模型更加符合实际。

Wenzhou Xidele Plastic Products factory was founded in1990 and is located in Xiannan Industrial Zone, Xianyan, Ouhai, Wenzhou.

浙江温州喜得乐塑料制品厂，位于温州市瓯海仙岩仙南工业区内，创建于1990年。

the middle crust with plastic deformation consists of a platy ductile flow zone and a ring-shaped re-melting zone.

中地壳为塑性流变层，由板状韧流带和环状重熔岩带构成；

The metal flow of slab in sizing was analyzed and the buckling and "fish tail" at slab head and end were studied with plastic collapse theory according to the mutual influence of end and deformation zone.

对减宽侧压过程的板坯金属变形流动情况进行了分析，并结合外端与变形区的相互影响，采用塑性失稳理论对板坯的失稳弯曲现象和头尾部鱼尾变形进行了研究。

The slip-line field and velocity field of plastic deformation zone in cutting metal are constructed by means of the mechanical boundary conditions and the ship-line field theory.

根据力学边界条件构造金属切削过程塑性变形区的滑移线场和速度场。

Ningguo Guoshun Rubber& Plastic Products factory is located in the wind King beautiful-at the foot of Huangshan Ningguo Heli economy Techno-logical Development Zone.

宁国市国顺橡塑制品有限公司座落于风景秀丽的黄山脚下-宁国市中溪工业开发区。

Brinson and his associates have also shown that material anisotropy exerts an effeet on plastic-zone shapes.

Brinson和他的合作者还表明,材料各向导性对塑性区的形状会产生影响.

After the feed zone, the screw flight depth is gradually reduced, forcing the plastic to compress.

经过输入这道关, 螺丝钉的螺口深度慢慢减小, 这样使得塑料压缩.