plate element的例句大全

Research results: The analysis process of frame bridge with skew angle has been given by use of MIDAS. We obtained the outcomes from two models and the difference between results with 2D rigid frame and 3D space model of thick plate element.

研究结果：给出了用MIDAS分析斜交框架桥的详细分析过程，得出斜交框架桥三维空间模型和二维平面模型分析的结果，并得出2种模型计算结果的差别。

The singularity of thick and thin plate element stiffness matrix due to the use of the reduced integration on the basis of the finite element is investigated.

本文研究了薄厚板壳有限单元统一性理论中，由于采用降阶积分而使得刚度矩阵产生奇异的问题。

A 4-Node, 24 Degree of freedom thin flat shell element based on the membrane-plate similarity theory

一个基于膜板比拟理论的四节点二十四自由度的平板壳单元

A 20 DOF hybrid stress element based upon Mindlin plate theory is developed by using the optimization design method for thin and moderately thick shell.

文章把杂交元的优化设计原理用于厚薄壳问题，构造了正交曲线坐标系中的Mindlin型四节点二十自由度壳元。

At first we explain the fundamental theory of perturbation method and derive all the formulae which are necessary to solve nonlinear problems using perturbation boundary element method. Then a plate subjected simple tension load is used to check the accuracy of employed theories and computer programs.

文中阐述了摄动法的基本理论，推导了摄动边界元法的全部公式，并以简单拉伸板为例对全部理论及计算机程序进行了检验。

Based on the 8-node isoparametric element of m edium/ thick plate, this paper builds up a element by means of introducing generalized con forming condition of shear strain and displacement.

在适用于中厚板的八结点等参数平板单元的基础上，通过引入剪应变与位移的广义协调条件，建立了一种平板单元。

Thick/ thin plate rectangular element based on finite strip

基于有限条带的厚/薄板矩形通用单元

This pater presents a separable Hamiltonian system in elasticity and its corresponding variational principle. Further its finite element method is taken to solve thick laminated composite plate problems.

本文给出弹性力学中可分的哈密顿系统及其相应的变分原理，用有限元法求解了强厚度复合材料叠层板问题。

The Elastic-plastic Finite Element Analysis for Stiffened Tension Plate with Eccentric Crack

加筋偏心裂纹板的弹塑性有限元分析

Application of thin-plate finite element in powerhouse water retaining wall design for hydropower plant

薄板有限元在水电站厂房挡水墙设计中的应用

In order to decrease the temperature grads, element balance method is presented in this paper to analyze the influence of some parameters on temperature grads of an air-cooling-plate-fin heat exchanger.

用元体平衡法对板翅式风冷换热器进行分析，从降低换热器的温度梯度入手，分析一些参数对温度梯度的影响情况。

Locking-free Thick Plate Bending Triangle Element

完全无闭锁厚薄板通用弯曲三角形单元

This information can be found on the flange or terminal block of the element or on the water heater data plate.

有关参数可以在加热元件的法兰或接线盒上找到，或者在热水器的参数板上找到。

CAD for unfolding of thick plate punched element in automobile frame

汽车车架厚板冲压件毛坯展开CAD

Thermal balance and finite element analysis of temperature field for hot runner plate

热流道板的热平衡及温度场的有限元分析

Transient temperature field analysis of functionally gradient material plate with temperature-dependent material properties under convective heat transfer boundary by finite element method

对流换热边界下变物性梯度功能材料板瞬态温度场有限元分析

This paper, based on the finite element method ( FEM) and utilizing two different means, analyzes the stress and strain field distribution of central through crack tip on a finite flat plate, and calculates the stress intensity factor of the crack tip.

基于有限元分析方法，对有限大平板中存在的中心穿透裂纹，分别用不同的方法分析其裂纹尖端应力、应变场分布，计算出裂纹尖端的应力强度因子。

Using MARC commercial software, tensile plate models of both all base steel and welded joint with various center through crack sizes were computed by three-dimensional finite element method, and the tensile process was simulated at the same time.

采用MARC商用软件，对不同中心贯穿裂纹尺寸的母材及其实际焊接接头拉伸板模型进行了三维有限元计算和拉伸过程模拟。

Stress analysis are presented for the main components such as thrust plate assemblies, pressing plate assemblies and oil cylinder seats used in large sized frame or chamber type filter presses by the finite element method.

针对大尺寸板框、厢式压滤机的油缸座、止推板体、压紧板体等主要承载构件，用有限元方法进行了应力计算。

Concerning of the interactions both between wheel-rail and linear induction motor ( LIM)-reaction plate ( RP) of this system, the vehicle-track vertical dynamic model is built based on coupling dynamics and dynamic finite element method.

本文基于动力有限元和耦合振动理论，考虑轮轨关系以及直线感应电机和反力板之间的相互作用，建立了直线电机地铁系统车辆轨道垂向动力学模型。