plate height的例句大全

The spherical particle sizes of the polymer are 5 ± 2 urn. Some column parameters such as the permeability, theoretical plate height and selectivity were determined and compared with the data of similar packings in the literature.

该球形聚合物的料径为5±2μm，测定了渗透性、理论塔板高度和选择性等柱参数，并与文献中类似填料的数据作比较。

Asked how cutting makes use of the rectangular plate height h minimum?

问如何切割使得所使用的矩形板的高度h最小?

In this paper, the load which the bolster plates transmit in hydraulic press are analyzed by finite element method with plane stress elements. The results of calculation show the effect of bolster plate height and load area on transmission of load.

采用平面应力单元，对水压机加载时垫板对载荷的传递进行了有限元分析，得到了垫板高度以及加载区域对力的传递的影响规律。

Kelley and Billmeyer indicated that the theoretical plate height describing zone broadening effect in mobile phase depends on the' molecular weight of solute only.

根据Kelley和Billmeyer描述流动相中峰加宽效应的理论，塔板高度和溶液的分子量有关而和分子量分布无关。

The effect of kinetic energy factor of gas phase, clear liquid height on liquid dispersivity of plate towers is studied in spray operation.

在喷射工况下，研究了气速及板上清液层高度对板式塔液体分散性能的影响。

The factors considered were jet velocity, spacing of nozzle-to-impinging plate ( height), slot width, angle between jet direction and plate, temperatures of impinged plate and water ( liquid) from the slot nozzle.

考虑冲击区对流换热的因素有射流的速度、射流出口距冲击板的距离（高度）、喷嘴的宽度、射流出口速度方向与冲击板之间的夹角、冲击板的温度及水温等。

Via analysis of different plate thickness combinations of equality height spacer plate group, contact stress curves and contact area distribution among the plates were got.

对整体高度恒定的垫板组的不同板厚组合进行分析，得到了不同组合时各层垫板间的接触应力曲线，并统计了各个接触层间的接触面积。

The surface of corrugated wire gauze packing was treated with different methods respectively and the pressure drop Δ P/ Z and the height equivalent to a theoretical plate HETP of packing were determined before and after they had been treated with ethanol water system.

对金属丝网波纹填料采用不同的方法进行表面处理，并以乙醇水为物系，对处理前后填料层的压降△P/Z及等板高度HETP进行了测定。

At the same time, different influences on node performance about different stiffened plate, beam web thickness, beam web height, concrete strength, axial compression ratio, shear span ratio are also obtained.

同时，通过建立不同的模型进行计算，分析了加劲板、型钢腹板厚度、型钢腹板高度、混凝土强度、轴压比、剪跨比等因素对节点性能的影响。

Forming and Curbing of Plate Bending in Jobbing Sheet Roiling Process ( 5) ── Rolling line height and offset effecting plate bending

中板轧制过程板坯弯曲生成与抑制之五&轧制线高度及轧辊偏移距对板坯弯曲的影响

The floating height of plate-strip is important work data of air cushion fur-nace, which affects the heating velocity and blower power consumption.

金属板材漂浮高度是气垫炉重要工作参数，影响到加热速度以及风机功率消耗。

Effect of United Casting Height of Gate Pier and Bottom Plate on Gate Pier Crack Control Further Analysis of the Method for Calculating the Integral Base Slab of the Water Gate

闸墩与底板连浇高度对闸墩防裂效果的影响水闸整体式平底板计算方法的再分析

Wire plate keep a certain height with ground, manually through the guide wire to wire to wire feeding tube body.

焊丝盘离地保留一定高度，通过人工把焊丝穿过导丝管送到送丝机构。

The bead height tracking technique using with welding current as a sensor is developed and testing weld on arc type tube plate for space curve scam is carried out. Finally, the technique is applied to automatic welding for boiler head and good results arc obtained.

研制了电流传感器焊缝高度自动跟踪系统，进行了弧形管板空间曲线焊缝自动焊接实验，并在锅炉封头焊接机中应用，取得了良好的效果。

The height of swing arm is regulated by the handwheel at the top of the machine and the cutting stroke is regulated by the timer so as to easily obtain optimal cutting position to improve work efficiency and prolong the service life of die cutter and padding plate.

摆臂的位置高低由机器上端的手轮调节，冲裁行程由时间计时器调整，这样可以轻易获得最佳裁切位置，提高了工作效率，延长了刀模和垫板的使用寿命。

Scale-up effect of fixed adsorption column height equivalent to a theoretical plate

固定床吸附柱放大效应考察&理论板当量高度分析

About horizontal tank, the calibration accuracy will be affected from the internal diameter of straight right cylinder, top plate, total height of dip hatch to tank bottom, degree of dip inclination, thickness of steel plate and measurement data of internal accessories of tank.

卧式油罐的检定精度受到直圆筒内径、顶板、下尺点内竖直径、倾斜度、钢板厚度及罐体内附件的测量数据的影响。

Loosen two fasten bolts on the seat of driven gear shaft, put the pad of required height to keep the balance of support plate, and ensure the even cutting.

松开从动齿轮轴支座上的两个固定螺钉，垫上所需高度的垫片，以保持左进料托板水平，保证割料后的切条均匀。

jinzun wine thousand blood, jade plate cuisine 10000 surname paste, zhu lei, when china leila off, singing a height of complaints, high.

金樽美酒千人血，玉盘佳肴万姓膏，烛泪落时民泪落，歌声高处怨声高。

in addition business card printing and membership card before the spray al paper (plate) store, stack height knife;

另边制卡和会员卡制作后的喷铝纸（不活）保存时，堆叠矮度答刀；