plate thickness的例句大全

The results showed: the subgrade soil had the minimal affection, the pile settlement affected most and pile spacing and bearing plate thickness were to a certain extent.

结果表明：桩间土体影响最小，桩沉降影响最大，桩间距和承载板厚度变化均有一定程度的影响。

this paper discusses how the welding groove and the plate thickness affect the sheet metal manufacture processes, and how to design with reasonable methods.

本文阐述了焊接坡口和板厚处理对钣金加工制造工艺的影响，并用合理的方式设计和处理。

The equivalent force caused by temperature field of plate are presented in structural analysis. The thermal flexure are caused by difference temperature along plate thickness. Numerical examples prove the accuracy of thermal flexure calculation. 3.

在热变形计算时，本文推导了板壳温度场导致的等效温度载荷，其中板厚方向的温差将引起板的热弯曲，数值算例表明了热弯曲计算的准确性。

While easily online detected parameters, such as plate thickness, coiling temperature, acid temperature and flow, were selected using orthogonal test method to predict the acid endpoint based on BP neural network.

按正交试验方法从生产线收集易于在线检测的钢板厚度、卷取温度、酸液温度、酸液流量四个工艺参数的数据，采用BP神经网络模型来预测酸洗结束时间。

The curve of relation of joint moment and rotation angle, end-plate thickness and forced load-bearing characteristic of bolt are analyzed;

对节点弯矩&转角曲线关系、端板厚度和螺栓受力特点进行了分析；

measurement method of the bone plate thickness with the dental implant as the center and its evaluation

以牙种植体为中心的骨壁测厚方法及其评价

Determination of stilling basin base plate thickness in Baishan hydropower station

白山水电站消能塘底板厚度的确定

Second, by changing the geometric parameters such as base panel thickness, base web thickness, base elbow plate thickness, base elbow plate amount and the shell thickness, have a research on the transmission rate of the various parameters.

第二，通过改变结构的几何参数如面板厚度、腹板厚度、肘板厚度、肘板数以及壳体厚度等，研究了各参数对传递率的影响。

Via analysis of different plate thickness combinations of equality height spacer plate group, contact stress curves and contact area distribution among the plates were got.

对整体高度恒定的垫板组的不同板厚组合进行分析，得到了不同组合时各层垫板间的接触应力曲线，并统计了各个接触层间的接触面积。

The slit width, wire diameters and plate thickness can be measured by application of diffraction, and it can be derived to measure the variables of interval, displacement, strain, section and the others.

运用衍射的特性，可以测量狭缝的宽度、细丝的直径、薄板的厚度等参数，并可派生到测量反映物体的间隔、位移、应变、剖面以及其它与此相关联的变量。

The article detailedly discusses the measuring principle of the γ-ray thickness indicator and the measuring methods of temperature compensation parameters. It is significant to improve on-line measuring and controling size precision and ensuring quality of steel plate thickness.

详细论述了γ射线测厚仪的测量原理及其温度补偿参数测试方法，对提高测厚仪在线检测及控制尺寸精度，保证钢板厚度质量有现实意义。

Influence of Mill Bilateral Stiffness Difference on Hot Rolled Wide Heavy Plate Thickness Deviation

轧机两侧刚度差异对热轧宽厚板两侧厚度偏差的影响

The parameters was set according to intrinsic structure of tin bath and the practical situation in field of production. The plate thickness and its deviation meet the demands of ITO customers.

结合锡槽的本体结构和生产现场实际情况进行了合理的选取，确保成形过程顺利进行，使得1.1mm超薄浮法玻璃的厚度范围和厚薄差完全能够满足ITO用户对玻璃基板的厚度要求。

practice proves this method can implement decoupling of steel shape and plate thickness, meets the requirements of steel plate quality, with excellent robustness.

实际运用表明，该方法能够实现板形板厚的解耦，满足板带质量控制要求并具有良好的鲁棒性。

Analysis and calculation of the pit base plate thickness of bearing resistance water foundation

抗承压水基坑底板的厚度分析与计算

Influence of Base Plate Thickness on the Interface State of Explosive Composite Material

基板厚度对爆炸复合材料界面状态的影响

Change the speed and base plate thickness of the flat panel, parameter sensitivity was analyzed and the structural response with these parameters was obtained.

改变结构的底板厚度和入水速度进行敏感性分析，得到结构响应随上述参数改变的变化规律。

The influence factors on the effective length factor such as the base plate thickness, the slenderness ratio, column section size and elastic modulus of concrete were studied based on the calculation of effective length factor of the specimen.

在对试验试件柱计算长度系数进行计算的基础上分析了底板厚度、柱截面尺寸、长细比以及混凝土弹性模量对计算长度系数的影响。

In order to fully used the compression resistance of the concrete, this paper analyzed the stress distribution to the composite beam in the actual use, and put forward to the method calculating the concrete flange plate thickness.

为充分利用混凝土的抗压性能，本文通过分析钢与混凝土组合梁使用阶段的应力分布，提出了一种确定钢梁上混凝土翼板厚度的方法。

Basing on the technique of variational analysis, this paper presents how plate thickness and geometry of spiral case and stay ring influenced its strength.

变量化分析是以参数化技术为基础的结构分析工具，它只需经过一次分析就可以获得设计变量在给定范围内变化时对结构性能的影响。