point contact的例句大全

Biomechanical research on new type point contact locking compression plate with osteoporotic comminuted radial fracture model

点接触锁定加压接骨板固定骨质疏松粉碎性桡骨骨折的生物力学特性

Based on point contact model of the inflatable rubber tires, the tire has been simplified. That are deduced included the radial force of the wheel, damping force, side force, self aligning torque ( SAT) and moment produced by yaw.

基于充气橡胶轮胎点接触模型，对轮胎进行了简化，并推导了跨座式单轨车辆各轮对的径向力、阻尼力、侧偏力和回正力矩以及走行轮的摇头力矩。

While traditional internal fixation technique is reform, the design of the plate is also improved. The concept of limited contact plate and point contact plate was introduced.

对传统内固定技术改革的同时，传统接骨板也进行了相应的改进，先后出现了有限接触、点式接触接骨板。

Three Dimension Finite Element Analysis and Biomechanical Study of the Point Contact Locking Plate System

点接触锁定接骨板系统的三维有限元分析及生物力学研究

Quick-point grinding is a new type of high and super-high speed grinding process with a point contact zone and lower grinding power, and the edge effect of the air barrier is weakened because of the thin super abrasives grinding wheel.

快速点磨削是一种新型高速/超高速磨削技术，接触区很小，实际磨削功率低，冷却及散热效果好。

Several cases are presented for point contacts including single asperity, wavy surface and real engineering rough surfaces, and also for finite line contact.

计算实例模拟了点接触单峰表面，正弦表面和真实粗糙表面的弹性接触以及有限长滚子线接触等接触问题。

This new three-node element, which is called sliding cable element, can simulate the cable sliding under a pulley by point contact, and it simplifies computations by automatically adjusting the cable segments on each side of the pulley.

被称为滑移索单元的新单元有三个节点，以点接触的形式模拟索从下方绕过滑轮，它可以通过自动调整两侧索段的长度而使单元处于平衡状态，从而简化了计算。

An experimental study of the conical cylinder point contact plate on cortical microcirculation

锥状点式接触钢板内固定对局部皮质骨微循环影响的实验研究

To determine the mechanical properties ( stiffness) and compression force of a new design of point contact plate, with the ability of dynamic compression for reducing the gap at the fracture site and enhancing the stability.

目的：研制一种可对骨折断端动力加压的点状接触接骨板，对其加压特性及固定的力学稳定性进行评价。

The geometrical relation of three and four point contact ball bearing

三点四点接触角接触球轴承的几何关系

Analysis and calculation of Minimum Allowance of Three Point and Four Point Contact Ball Bearing Raceway

三点四点接触球轴承沟道最小余量的分析与计算

VT breakdown reasons and treatment methods of neutral point contact gap of GIS

GIS中电压互感器中性点接地间隙击穿原因及处理方法

The results show that the point contact and line contact friction coefficients of the steel-steel pairs take on declining trend with increasing the test load under dry lubrication.

结果表明，在试验范围内，随着试验负荷的增大，钢-钢摩擦副在干摩擦条件下线接触摩擦因数和点接触摩擦因数呈逐渐下降的趋势，这种下降趋势在线接触时尤为明显；

Utilizing the theory of differential geometry, elastic deformation and wear abrasion and running-up of the tooth surfaces in circular arc gears, an elastohydrodynamic lubrication ( EHL) model of point contact with two-dimensional surface velocities was developed.

从圆弧齿轮齿面微分几何分析、弹性接触变形和跑合磨损分析，建立了具有二维表面速度的点接触弹流基本模型。

Experimental Research of Sliding Friction Coefficient of Rough Surface under Lubricated Point Contact

润滑点接触粗糙表面滑动摩擦因数的实验研究

This paper investigates forces applied on port plate surface of point contact axial piston motor, and introduces a solution of the problem of additional tilting moment of the cylinder body caused by applied force not on supporting point.

本文通过研究点接触式轴向柱塞马达配流面的受力情况，介绍了运用静压平衡理论设计平衡油室的办法，解决缸体上存在的由于作用不在支承点上所造成的附加倾复力矩的问题。

A further research on the third order contact analysis of point contact surfaces

点啮合齿面三阶接触分析的进一步探讨&V/H检验法的理论

It is different from under point contact that there is no stick area under line contact in the partial slip regime, and load distribution within line contact area is uneven due to roughness of surface.

磨痕分析表明，承载区域接触不均匀，存在虚接触区域，其大小与表面粗糙度有关，而接触区域没有不磨损的粘着区，不同于点接触形式。

Take the example of three point contact ball bearing applied on the spindle of advanced aircraft engine, its dn value and work temperature are very high, often causing the contact thermal failures.

如先进航空发动机主轴采用的三点接触球轴承，其dn值和工作温度非常高，经常造成摩擦副发生热失效。

This paper describes the performance test, contact fatigue strength test and bending fatigue strength test on the gear reducer of involute point contact Ferrographical analysis is made.

本文对渐开线点啮合齿轮减速器进行了性能试验、接触疲劳强度和弯曲疲劳强度试验，同时还进行了铁谱分析。