point load的例句大全

In the paper, a panel excited by either point force load or circle force load is modeled to study its vibration responses. Based on the theoretical model, the responses of a simply supported flat panel under two types of excitations are predicted and analyzed.

建立了平板结构在点力载荷和线力载荷作用下振动响应的理论模型，应用该模型计算出简支平板在两种载荷作用下的振动响应，然后进行比较分析。

The key point of load-out was keeping the deck slide way flushing with the dock slide way by controlling the floating state in the whole process.

这种下水方式的关键是在作业过程中驳船的浮态调整，使甲板滑道与码头滑道始终保持平齐。

Through researches on the ( ultra-) supercritical boiler under different conditions of temperature distribution point wall, the temperature control line ( A line) of safe operation under different load is obtained.

通过对超（超）临界锅炉不同工况点管壁温度分布情况的研究，得到了不同负荷下的安全运行温度控制线（A线）。

From the point of view of design, puts forward method to develop the ventilator operating within the limits of load.

并提出从电机设计方面实现限载型通风机的方法。

By load, I mean the point along the shaft at which the rod flexes.

我的意思是沿着竿身的弯曲点。

The results of load test showed when a load within design scope passed the bridge, the biggest quoin of bridge face center in the measure point was 1 ° 02 ′ 44.7 ″.

荷载试验检测结果显示，当设计荷载内的荷载通过该桥时，检测点中桥面的最大转角为1°02′447〃，表明桥身侧向稳定性好。

In this paper, a high-speed framing camera is used to seize the transient process of crack propagation. Under impact load, dynamic energy release rates of the running crack tip of a three-point-bend beam with initial crack are studied by means of dynamic caustics.

借助高速摄影捕捉裂纹瞬态扩展过程，利用动态焦散线研究了含有裂纹的三点弯曲梁在冲击载荷作用下扩展裂纹尖端的动态能量释放率分布规律；

research on dynamic load emulation is a hot point of test bench study.

基于电机的负载模拟技术是试验台研究的热点之一。

Based on the structure of micro load displacement tester, developed in Institute of Precision Engineering, Xi'an Jiaotong University, some issues on judging initial contact point were investigated in details.

本文利用西安交通大学精密工程研究所研制的微力微位移测试仪，对初始接触点判断的相关问题进行了深入研究。

In the rod pumping wells production process, it is required continuous monitoring load and displacement of suspension point.

在抽油机井生产过程中，需要不断地监测悬点载荷与悬点位移。

The results show that the point contact and line contact friction coefficients of the steel-steel pairs take on declining trend with increasing the test load under dry lubrication.

结果表明，在试验范围内，随着试验负荷的增大，钢-钢摩擦副在干摩擦条件下线接触摩擦因数和点接触摩擦因数呈逐渐下降的趋势，这种下降趋势在线接触时尤为明显；

The defect that there are potential pressure of mobility anchor point ( MAP) load and high communication cost in multilevel hierarchical mobile IPv6 are analyzed.

分析了多层移动IPv6结构中存在移动锚点潜在负载压力大及通信开销高的弊端。

Based on the law of conservation of energy and the analysis of the detailed movement of beam pumping unit by complex vector analysis, mathematical model of electric current, polish rod load and point of suspension displacement was established.

以能量守恒定律为基础，同时利用复变矢量法对游梁式抽油机的运动规律的分析，建立了电流与光杆载荷及悬点位移之间关系的数学模型。

Eventually, the database will saturate the CPU or disks and at that point the response time will rise as additional load is added.

实际上，随着额外负载的增加，响应时间急剧攀升，数据库就会耗用CPU或者磁盘。

Theoretic Expression of Silicon Solar Cell Load Resistance at Maximum Power Point

晶体硅太阳电池最大功率下负载的函数表达

Effect of Land Use/ Cover Change on Pollution Load of Non-Point Source in Upper Reach of Yangtze River Basin

土地利用/覆盖变化对长江上游非点源污染影响研究

The load factor for 4-point bending test, whose derivation is usually not included in textbooks, is also derived in this paper.

简要地导出了一般教材上较少提及其推导的四点弯曲加载因子。

The Deflection Performance Analysis of Single-layer Cable Net for Point-supporting Glass Curtain Under Horizontal Load

水平荷载作用下点支式玻璃建筑单层索网体系的变形性能分析

The methods of calculating electronic map load and confirming key scale based on special point were brought forward in innovational. And it established multi-scale display model of electronic map of national boundary.

创新性地提出了电子地图载负量的计算方法和基于特征点的关键比例尺确定方法，建立了国界电子地图多尺度显示模型。

The preparation of the C language program and using of the operating elements "truth table" to divide the load point outage type makes it much simpler than previous method to the judgment of the outage type.

编制了C语言程序，运用操作元件真值表来划分负荷点的停运类型，使得停运类型的判定比前一方法更简单。