polished surface的例句大全

The solution: the roll surface coating rollers should be ground and polished.

解决办法: 涂布辊辊面应磨细、磨光.

Cold solidifying surface anti-contamination agent of polished tile was prepared.

本文研制了室温固化的抛光砖表面 防污 剂.

The study surface of each specimen was polished to# 1000 by silicon carbide abrasive paper.

每个试样的测试面经碳化硅水砂纸逐级磨光至1000目。

Polished Tile Surface Pro of ing

抛光砖表面防污技术研究

Certainly wants the grain to raise, reduces the polished rice fine surface, must coordinate suitably.

一定要五谷为养, 减少精米精面, 要适当地配合.

A test-piece is shaped into a beam of about 20 cm length and its upper surface is highly polished. The test-piece is bent convex upwards; on that occasion one had better plan the maximum bending stress to be about 20 bar or less.

试件加工成20cm长的梁，并高度磨光其上表面，把它弯成向上凸，其最大弯曲应力宜为20bar或稍小一些。

Abstract: Abrasive flow machining ( AFM) is an effective way to the irregular surface and internal structure of parts polished, debarred, filleted finish machining and so on.

对于不规则的零件表面及内部结构的抛光、去毛刺、倒圆等精加工，磨粒流加工是一种有效的加工方法。

The mosaic approach and fixture method can be applied to fix the sample avoiding the round polished edge and make sure the smoothness of the testing surface.

试样抛光时，最重要是要避免夹杂物的剥落、变形或抛光表面被污染，以便检验而尽可能干净和夹杂物的形态不受影响。

It is made of precise ceramic and polished up to Ra0.2high hardness and smooth surface enable the enameled wire free from hurt during surface sliding.

此产品由精密陶瓷加工，超精抛光达Ra0.2，由于硬度较高，表面光滑，漆包线在其表面滑动时顺畅不受损伤。

Study of the attachment of cementum extract to the polished titanium surface

牙骨质基质提取物吸附于光滑钛表面上的实验研究

Objective: To study the attachment of cementum extracts to the polished titanium surface.

目的：探讨牙骨质提取物能否良好地吸附在光滑钛表面上。

Conclusion: Cementum extracts can bind to the polished titanium surface very well.

结论：牙骨质基质提取物能较好地吸附在光滑的钛表面上。

Attachment and Migration of Osteoblast on the Polished Titanium Surface by Cementum Extracts

牙骨质基质提取物促成骨细胞在钛表面上粘附与移行的实验研究

The surface has been polished shiny bright.

面儿磨得很光。

In order to gained a copper surface of high quality and unknit, the experiments that copper was polished using colloidal silica slurry on fixed conditions were done, in which the curve of mechanical reaction between the concentration of abrasive particles and polishing rate was found.

为得到高质量、高平整度的铜表面，采用SiO2溶胶抛光液对铜进行抛光实验，在给定的条件下，得到了磨料粒子的浓度与抛光速率间的机械作用曲线。

Conclusion: Color change of pure titanium is not related to surface configuration, but to whether it is polished.

结论：纯钛铸件表面粗糙度对颜色稳定性的影响与其表面形态无关，而与其表面是否经过抛光有关。