position error的例句大全

To decrease the tracking error in AC position servo control system, a novel design approach of zero phase error tracking controller ( ZPETC) is proposed, which is called Extended Bandwidth Zero Phase Error Tracking Control ( EBZPETC).

本文针对位置伺服系统中存在的跟踪误差，研究了零相位跟踪控制的交流位置伺服系统，提出了一种简便易行的设计零相位跟踪控制器的方法&扩展频带零相位跟踪控制。

Implementation of Coarseness-Precision Combining and Error Correcting in Shaft Position Encoders

轴角编码器中的粗精组合与纠错技术实现

Machining Precision of High Precision Axial Assembling Dimensional Chain, Assembling Technology and Analysis of Error in Shape and Position in Exchangeability of Guide Apparatus

导水机构互换性中高精度轴向装配尺寸链的加工精度、装配工艺和形位误差分析

The results from accuracy and precision tests of the instrument show that the maximum error in Raman peak position measurement is ± 1 cm-1.

经对仪器准确性和精密度的测定表明，测定拉曼峰位的最大偏差为±1cm－1。

Comparing with conventional function based on generalized likelihood ratio, the new one considers estimate error in fused target position, which is more accurate to reflect the relationship between measurements and targets.

与传统的基于广义似然比的代价函数不同，改进的代价函数在计算中融入了目标位置的估计方差，能够更加准确地反映量测与目标之间的相关程度。

The reason of the error in axle-angle position coder for precision tracking and instrumentation radar is analyzed in this paper, and the concrete measures of controlling the error are also proposed.

分析了精密跟踪测量雷达用轴角编码器产生测量误差的原因，并结合实际提出了控制测量误差的具体措施。

This paper analyses the basic philosophy of coarseness-precision combining and its error correcting in a shaft position encoder. On the basis of a 160DD × 4/ 16 multiwire rotatory transformer, a simple method of correcting encoding errors is given by using pure hardware circuits.

本文分析了轴角编码器中粗精组合与纠错的基本原理，并基于160DD×4／16多线旋转变压器，提出了运用纯硬件电路实现编码纠错的一种简单方法。

It is discussed that the system error and dynamic error, especially the dynamic error in position algorithm.

讨论了捷联式惯性导航系统的误差，对位置计算中的涡卷误差进行了推证。

Error analysis of the center of gravity method when used to get the position of a facula

利用重心法求光斑信号位置的误差分析

Calibration of position detecting error for improved 2-dimensional position sensitive detector

改进型二维位置敏感探测器检测误差的校正

In the teaching of vertical angle measurement, as to the concepts concerning the correct position of vertical index mark and vertical index error, some textbooks haven't presented an exact description of it.

在竖直角测量教学中，对于竖盘指标差及竖盘指标的正确位置等概念，在一些测量学教材中往往表述得不够确切。

It determines the optimum opening rate and opening position. ( 3) Model tests and numerical results are consistent with their difference is within the range of allowable error, and they can confirm each other.

模型试验与数值计算结果相符合，在误差允许范围之内，二者相互印证。

Unequal Error Correction Protection for Video Based on Position Rearrange

基于位置重排的视频不等纠错保护方法

Analysis the video compress technique error tracking and reference picture select based on feed-back channel. Identifying the position of error block in error frame or in the error propagation frame by error tracking firstly, then recovering the error by Multi-RPS.

在系统分析基于反馈的差错跟踪和参考帧选择技术的基础上，利用差错跟踪技术标志出错帧和差错扩散帧中的错误宏块的位置，然后采用多参考帧选择技术恢复差错。

To separate the error factor and mounting error for gyro and accelerometer respectively, a 16 position calibration scheme was given, which would segregate 42 factors.

为分离陀螺仪误差系数、加速度表误差系数、陀螺仪安装误差、加速度表安装误差，设计了一个16位置的标定方案，以完整地分离出惯性平台的42项误差系数。

The performances of EMB system are directly affected by position measurement error.

在电磁轴承系统中，位置测量误差直接影响着系统性能。

Popper will place the "wrong" question in the beginning position in his own philosophy epistemology, will have the unique opinion to the error problem. It can be said that the core of his entire scientific philosophy will be surrounded by the error problem.

波普尔将错误问题放在自己哲学认识论中的起点位置，对错误问题有自己独特的见解，在一定意义上说，他的整个科学哲学思想体系都是围绕错误问题而展开的。

The position relationship between beam axis and shaft axis was discussed in lapping with bending disk. The equation denoting the best distance of beam axis and shaft axis was set up, and the error was analyzed.

本文讨论了磨具弯曲成形法中梁轴线与转轴中心线位置之间的关系，给出确定梁轴线与转轴之间最佳距离的计算公式及误差分析。

Through time aligning to the quality datum of strip steel, established the tracking algorithm between the quality data of strip steel and the lengthways position. Finally, the paper discussed the measure for correcting the length error.

通过对带钢各质量数据的时间对准，建立了精轧出口后的质量数据沿带钢长度方向上的位置跟踪算法，探讨了带钢长度误差的修正措施。

In consideration of inaccuracy of the dynamic model of a multiple manipulator system, the error equations on object position and internal force are derived. Then a hybrid position/ force coordinated learning control scheme is presented and its convergence is proved.

考虑多机械手系统的动态模型不确定性，导出了物体位置的误差方程和内力的误差方程，给出了多机械手的混合位置/力协调学习控制策略，并对学习控制的收敛性进行了讨论。