pressure element的例句大全

The three-dimension finite element precise model of helical gears is established and impacting calculation is made in this model, the von mise stress, contact pressure and distortion are compared with in different engaging speed and time.

建立了斜齿轮三维有限元精确模型，并进行了冲击有限元计算，综合比较了在不同接合转速、不同接合时间工况下，斜齿轮各部位的应力、接触压力和变形状况；

In combination with a linear wire wound potentiometer and a cam-actuated angle displacement sensor, a hydro-electric proportional relief valve is used as pressure controlling element of hoist system to compose an open loop control system for overload protection.

采用电液比例溢流阀作吊机系统压力控制元件，与线性线绕式电位器和凸轮构成的角位移传感器一起组成吊机过载保护开环控制系统。

Finite Element Analysis of Stress and Contact Pressure of Rubber O-sealing Ring with Back-up Ring

O形橡胶密封圈配合挡圈密封的应力与接触压力有限元分析

A new technique by computer has been used to trace fatigue growth of surface crack of out corner of cylindrical pressure vessel nozzles by using the methods of 1/ 4 displacement and finite element.

运用1/4点位移法和有限元技术对圆筒型容器接管外拐角表面裂纹扩展时应力强度因子的变化作了计算机数值跟踪。

Study and Manufacture of High Pressure Wet Digester and its Application to Trace Element Analysis in Human Body

高压湿法消化器的研制及其在人体痕量元素分析中的应用

The dynamic coefficients of tilting pad guide bearings are derived with the help of finite-elements using pressure parameters partial differentiation.

本文采用有限元法，利用压力参数法和偏导数法直接推求分块可倾瓦导轴承的动力特性系数。

By using the method of level layer element, the distribution of passive earth pressure is analysed.

利用水平层分析法, 分析被动土压力的分布规律.

Distribution of removed material in Fluid Jet Polishing ( FJP) was investigated in experiments. The characteristics of fluid velocity and pressure on the sample surface were simulated using Finite Element Method ( FEM) when the fluid jet impacts the work piece.

实验研究了液体喷射抛光技术的材料去除量分布特征，并利用有限元分析方法，分析了抛光头（液体柱）与工件表面相互作用时流场的分布特点。

Finite element method for hydraulic computation of pressure irrigation system

压力灌溉系统的水力计算有限元分析

Statical analysis with finite element method is performed to pressurized pressure vessel of titanium alloys.

对型号主体系统中的钛合金气瓶进行有限元静力学分析。

Type-C spring Tube is a kind of sensitive elastic element of pressure gauge.

摘要C型弹簧管是压力仪表的敏感弹性元件.

The weighted pressure time history in each element was used to deduce the average overpressure variation on target surface.

对目标表面计算单元的压力进行面积加权平均，得到目标各表面平均超压随时间变化的曲线。

There is Burst disk pressure in the gauge, blow out hole in the back to relief the presure inside caused by failure of elastic element.

背部，设有泄压后盖及泄压孔，以释放因过载弹性元件破裂而产生的内部压力，增强了人员及设施的安全性。

Through finite element numerical calculation and experiment test on pressure vessel containing inner portrait surface crack, the results show that;

通过对一台含内壁纵向表面裂纹的实物压力容器的有限元数值计算和实验测试，结果显示：初始椭圆形表面裂纹在疲劳扩展过程中形状逐渐趋圆并保持圆形继续扩展。

It discusses new methods including in out boundary element method and forecast of temporary supporting pressure during the initial stage of excavation.

内外边界元方法和开巷初期临时支护压力预测等新方法。