process heating的例句大全

Back pressure is higher than 85 % are production process heating equipment, one of the best trap.

背压率大于85%,是生产工艺加热设备最理想的疏水阀之一.

These advantages make it possible to become the ideal means of stabilizing process heating of the blank.

这些优点使感应加热成为当今坯料稳定化处理加热的最理想的手段。

Verification indicate this simulation system can simulate slab heating whole process and optimize slab running velocity and temperature condition schedule of furnace operation and provide on-line control with optimum data.

验证表明，该系统能有效地模拟钢板在炉内加热升温的全过程。可以对炉辊速度和炉区温度进行寻优计算，为在线控制提供辊速及炉温制度最佳数据。

Abstract: Glass heating in horizontal tempering furnace is a dynamic process, the system, controlling, design and install of the tempering furnace make influence of this process.

在水平钢化炉中玻璃加热是个动态的过程，钢化炉的系统、制和设计安装质量影响这一过程。

Discussion into Heating Process Property and Beehive Construction of Ceramics

陶瓷蜂窝体结构及热过程特性探讨

And design of the temperature sensor and output circuit simulation of thermoelectric boiler heating process.

并设计了温度传感器和输出等外围电路，模拟了热电锅炉供热的过程。

The Multiwell heating, throttling refrigeration and low-temperature separation process have been applied in the gas gathering station of the Yulin gas field.

为彻底解决该问题，先后在榆总站建设了两套大面积换热、节流、低温分离工艺装置，并在现场进行了工业性试验。

In addition, the U-shaped interface, which minimizes electron crowding and localized heating effects, increases the mean time to failure by electromigration. Consistent, repeatable blanket film property and good parametric electrical test results have proven the production worthiness of this process.

此外，使电子阻塞和局部加热效应最小化的U型界面，提高了电子迁移失效的平均时间，一致的、可重复的覆盖膜特性和良好的电参量测试结果已经证实了这种工艺的生产价值。

Discussing on Choosing and Arrangement the Burner Using in Big Car Type Heating Furnace Burning the Natural Gas Transfer case sprocket production through the sinter hardening process

大型天然气台车加热炉烧嘴选型及布置的探讨用烧结硬化工艺生产汽车分动箱链轮

Using the methods of thermogravimetry and differential scanning calorimetry ( TG-DSC), study the regularities of fusion characters in different geological time by analyzing the performance of TG-DSC curves through heating process.

利用热重法和差示扫描量热法（TG-DSC），通过对煤灰升温过程在TG-DSC曲线上的表现特征进行分析，研究不同地质年代的煤灰内矿物组成差异对熔融特性的影响规律。

Mechanism, parameters and advantages of a deburring process by heating are described, by which process burrs on silicon steel sheets and on the edge of Aluminium guide strips of the motor rotor are removed through heating.

本文介绍了一种脱壳去毛利工艺，即用加热法去除电机转子硅钢片和铝导条边缘毛刺工艺的机理、参数及优点。

Through the heating experiments, get the temperature change law of the Al-Si alloy in the actual heating process, and compared with the simulation results.

通过周向加热实验，得到铝硅合金在实际加热过程的温度变化规律，并与模拟结果进行对比。

According to austenite isothermal transformation diagram, a heat treatment process for producing the left and right pincers through fixed heating time and the position was put forward.

借助奥氏体等温转变曲线，创立了定时定位的热处理工艺方法，用于左右钳口的生产，一次达到设计要求，简便可靠，省时节能。

The heat transfer mode described in this paper is used to research the heat conduction process of coal in coke oven chamber through the heating wall. The numerical solution of the model uses finite difference method by electronic computer.

传热模型用于研究焦炉炭化室内煤料通过炉墙的导热过程，模型用有限差分法由电子计算机进行数值解。

The effect of preheating treatment process of cold rolls on induction heat quenched structures and the effect of heating temperature and time on structure and hardness have been studied.

研究了轧辊的预备热处理工艺对感应加热淬火组织的影响，感应加热温度和时间对组织和硬度的影响。

The induction heating equipment and heat treatment process of thick-wall pipe were reconstructed.

对厚壁管感应加热设备及热处理工艺进行了重新设计改造。

Analyzing the transformation mechanism of titanium and titanium hydride. It makes the use of the fact that titanium hydride releasing hydride at 300 ℃, to design and process the Hydrogen Generator as well as its heating circuit.

详细分析了钛与氢化钛的转化机理，并利用氢化钛在350℃放氢的原理制作了氢发生器，以及其加热电路，并加工测试。

Thermal cycling absorption process ( TCAP) in a full reflux mode was studied at different feeding ratios, feeding places and heating/ cooling temperatures.

分别在不同进料比、进料位置、加热/冷却温度的条件下，对TCAP工艺的全回流模式进行了实验。

The electrode is electrified during the thermal bonding process, which heats the electrode quickly. The heating process improves the ductibility of the electrode, which obviates the fracture of the electrode.

在热键合过程中，对金属微电极进行通电，使其温度迅速升高，以提高其自身延展性，进而避免电极产生断裂。

Due to a great deal of limitation of heating by flame or laser, a new thermal stress forming process& high frequency induction heating forming of plate is studied in this paper.

由于火焰或激光局部加热存在着诸多局限性，因此本文研究了一种新的板料热应力成形技术&高频感应弯板成形工艺。