process sheet的例句大全

research on writing process sheet and drawing process picture sheet in integrated system

集成系统中工艺卡片填写与工序图绘制的研究

In this paper, the characteristics of sponge rubber sealing strip by microwave curing continuously are introduced, as well as the design in the compound formula of sponge rubber sealing strip, the design in die sheet, and the determination in technological process and processing conditions.

介绍了微波连续硫化海绵密封条的特点，以及海绵密封条胶料配方的设计、口型设计、生产工艺路线和工艺条件的确定。

Experimental study on the effects of material structure during thin sheet drawing process

材料组织性能对薄板拉深工艺影响的试验研究

Strain rate dependences of tensile failure process for single graphene sheet: A molecular dynamics study

单层石墨烯薄膜拉伸破坏应变率相关性的分子动力学研究自动薄层[膜]涂布器

By oxidization method of ore+ iron sheet, a foamed slag has been made, the phosphor in steel has been removed by large numbers of slag in melting terminal phase and oxidizing initial stages, thereby the process requirements have been reached.

采取矿石+铁皮的氧化方法造泡沫渣，利用熔化末期、氧化初期大法量去磷，从而达到工艺要求。

This paper discusses the design philosophy, global structure and operation sheet of remote sensing library in the terrain feature knowledge library, and parses some key technologies involved in the realization process.

论述了地物波谱知识库中遥感模型库的设计思路、总体结构和运行流程，并就实现过程中涉及的部分关键技术进行解析。

The special requirement and superior performance against corrosion of 2RE69/ Zr702 clad tube was summarized comprehensively. Otherwise, the type of joint, welding process between tube and tube-sheet, fabrication, assembly, test& inspection of distributor was expounded briefly in this paper.

介绍了2RE69/Zr702双金属管的特殊结构、优良耐蚀性能，与管板的连接接头型式及焊接工艺、管头及液体分布器加工、装配和试验。

This process include as follow: first, using high sizing accurate single side copper-clad thermoplastic resin sheet.

该工艺包括（1）采用高尺寸精度的单面覆铜箔热可塑性树脂片；

Surface Check and its Prevention during Post forming Process of Thermosetting Resin Impregnated Decorative Laminated Sheet

热固性树脂装饰层压板后成型过程中产生裂隙的原因及预防方法

The reason of surface checks developed during post forming process of thermosetting resin impregnated decorative laminated sheet was discussed.

本文讨论了热固性树脂装饰层压板后成型过程中，表层易产生裂隙的原因，并提出了若干防止产生裂隙的建议。

In order to solve the problems of the conventional gravity sludge thickening, the process of flat sheet membrane for sludge thickening ( MST) was used to thicken aerobic activated sludge.

为了解决传统污泥重力浓缩存在的问题，采用平板膜浓缩污泥（MST）工艺进行了中试。

Finite Element Simulation for Blanking Process of Thick Sheet Metal and Optimize Parameter

厚板冲裁过程的模拟仿真及其参数优化

It describes the problems frequently occurred during of large thick steel sheet and remedy and regulates the automatic flame cutting process for large thick steel sheet

介绍了厚大钢板自动气割过程中经常出现的问题及处理方法，并对厚大钢板的自动气割工艺进行了规范

And then reduced model is founded, warping deformation of variant bracing diaphragms and sheet metals at optima laying angle are surveyed, finally the process to upraise the rapid prototyping precision of the thin shell parts is set up.

建立简化模型，在最优摆放角度条件下，研究了不同支撑的薄片和薄板的翘曲变形，提出了提高薄壳零件快速成型精度的工艺。

Analysis of Preheating Temperature Influence on Sheet Metal Laser Forming Process

预热温度对金属激光弯曲成形过程的影响分析

Composition an Forming Process of Thin Sheet Glass and its Application

薄板玻璃的用途、组成和成形工艺

The Process Investigation of Punching Thin Sheet Under Tensile Stress

拉应力薄料冲裁工艺研究

The investigation on penetration process of projectile initiated by impact onto thin sheet

冲击起爆弹丸对薄板侵彻过程研究

Constantly Improved Raschel Lace Machine The Process Investigation of Punching Thin Sheet Under Tensile Stress

不断发展中的拉舍尔花边机拉应力薄料冲裁工艺研究

The technology of sheet metal hydroforming is new plastic process technology, which is rapid developed in recent decades. It can achieve the forming of complicated thin sheet metal, get good quality part and save much cost of model.

板料液压成形技术是最近几十年迅速发展的新型塑性加工技术，能完成一些复杂薄板零件的成形并获得较好的表面质量，而且能大大节省模具成本。