process shrinkage的例句大全

The numerical simulation of3D temperature field of castings during solidification process was carried out and the shrinkage cavity and porosity of sample castings were predicted using G/ R method.

对铸件开展了凝固过程三维温度场数值模拟，并应用G／R法对铸件进行了缩孔缩松预测。

Study on the spinning process of high shrinkage polyester fiber

高收缩聚酯纤维纺丝工艺的研究

During the casting process, The traditional Sterling silver alloy is prone to absorb air, oxidize and it has poor fluidity, and the tendency of shrinkage porosity in the castings, and is easy to blacken the casting surface.

传统斯特林银合金铸造时容易吸气氧化，流动性较差，有缩松倾向，铸造毛坯件表面容易发黑。

the author believes that the triply different fibre with a total size less than 111 dtex can be turned out from two different shrinkage polyester chips by double-screw composite spinning, which is considered as an advanced process.

文中对三异纤维的工艺路线进行了探讨，认为采用收缩性不同的两种涤纶切片，利用双螺杆复合纺丝技术生产出总纤度小于111dtex的三异纤维的工艺路线是先进的。

Numerical Simulation of Solidification Process of Steel Ingot and Shrinkage Prediction

铸钢锭凝固过程数值模拟和缩孔缩松预测

Derivation of Boundary Shrinkage Formula for Round Fruit during Drying Process

干燥过程中球形果蔬边界的收缩方程

During the developing process of one V-6 type engine intake manifold with 319.0 alloy, many defects as shrinkage and pin hole occurred frequently, which hindered its normal supply and thus affected the OEMs productivity.

国内某款乘用车V型6缸发动机进气歧管（319.0）开发过程中，屡屡出现缩孔、气（针）孔等铸造缺陷，严重地影响了供应商的正常供货以及整车厂产能的提升。

Numerical simulation of moisture diffusion in the Xianggu mushroom drying process with shrinkage

考虑收缩的香菇干燥过程模拟研究

The intensification of immiscible element in this process is the key to realize uniformization sintering and reach a higher shrinkage ratio.

加强非西安理工大学硕士学位论文一互溶性组元在此方面的功用作用是实现此类材料均匀化、高收缩比烧结的关键。

This article expatiates the reason of shrinkage and warpage of thermoplastic material part from aspects of material performance, part design, mould design and process parameters.

本文从材料性能，产品的设计，模具设计及加工工艺四个方面全面阐述了引起产品收缩变形的原因及注意事项。

Consequently, the percentage of tangential shrinkage ( yT,%) proved much less than that of radial shrinkage ( yr,%) throughout the whole drying process until the MC reduced to 5% and lower.

因此，在整个干燥过程中直到含水率降到5%及更低为止，弦向收缩的百分率（Y T，%）都远小于径向收缩的百分率（y r，%）。

selection of shrinkage rate and process parameter becomes a difficulty in precision plastic parts production.

精密注塑模具设计时的收缩率选取和注塑工艺参数设定已成为精密注塑件生产中的两大难题，所以很有必要对注塑制品收缩规律进行研究。

in the process of mixture design, such as mechanical property shrinkage anti-freeze and durability, pavement performance is tested and verified to reach mixture optimum fly ash content and optimum mixture.

同时，对掺粉煤灰水泥稳定碎石进行配合比设计，并通过力学性能、收缩性能、抗冻性能和抗疲劳性能等路用性能进行验证，得出混合料最佳粉煤灰剂量和最优配合比。

Detailed introductions are made on the factors, such as material selection, mold design, determination of shrinkage rate, injection molding process and property control for the melt processible fluoroplastics PVDF.

详细介绍了花篮原材料选择、模具设计、收缩率的确定、可熔融性氟塑料PVDF注射加工工艺及产品性能控制等影响因素。

dining room process repeatedly consideration, also on the column 1: in fact short skirt and sparerib are similar they all would shrinkage.

食堂经过再三考虑，也在栏上涂了一句：其实短裙与排骨一样它们都会缩水。

new process of reducing the washing shrinkage of rabbit hair knitted fabrics

降低兔毛针织物缩水率的新工艺研究

The process conditions and points to controll elasticity, width and weft shrinkage were presented.

文中给出了染整加工中的工艺条件,指出了在整个加工过程中控制弹力 、 门幅及纬向缩水的注意事项.

During the manufacturing process a plant usually experiences a degree of material shrinkage.

在生产过程中,工厂通常总要受到一点材料上的损失.

Solvent effect and volume shrinkage ratio in melamine-formaldehyde gel aging process were discussed.

介绍了三聚氰胺 - 甲醛凝胶老化过程的溶剂效应及其对体积收缩的影响.

A large number of mined-out areas usually formed, in the process of mineral resources exploitation, Open-stope method including breasting mining method, room-and-pillar method and shrinkage mining method were adopted in underground mine.

地下矿山应用全面法、房柱法及留矿法等空场类方法进行矿产资源开采过程中，通常会形成大量的采空区。