production procedure的例句大全

But while fans snap up these i-products, people in China are paying for the production procedure with their health.

但是当粉丝们抢购这些i产品时，在中国，有的人却为该产品的生产过程付出了他们的健康。

and the methods of schedule decomposing and task distributing are researched on. chapter 4 firstly analyzes the characteristic of synergic production procedure, and establishes the multi-mode production procedure monitor based on virtual stock.

第四章在分析协同生产过程特征的基础上，建立了基于虚拟库存的多模式生产过程监控方法，划分与定义了监控的级别，提出了具体的监控方法。

The feature, classification and production procedure of warp knitting fusible interlinings were presented in the article.

本文介绍了经编粘合衬的特点 、 分类和生产流程.

Inspect the execution state of production procedure on site.

巡查生产过程中的工艺执行情况.

This system achieves material management of production procedure by collecting bar code information from production procedure in real time and presenting material flow information of production procedure exactly.

该系统采用计算机二级工业网络方式，对生产各环节的条码信息进行实时数据采集，及时准确了解生产的物资流动，从而实现生产过程中的物资管理。

Objective To optimize the production procedure of Yangyin Qingfei Syrup ( YQS), improve the clarity, and reserve more active components in water extract solution of YQS.

目的优化养阴清肺糖浆的生产工艺，更好地保留有效成分，提高药液的澄清度。

during each production procedure of grape wine, acetic acid bacteria contamination easily occurs.

在葡萄酒生产过程的各个环节都可能受到醋酸菌的污染。

This thesis is concerning the acetylene production procedure through pyrolysis natural gas by thermal plasma jet.

本文报道热等离子体射流裂解天然气制乙炔过程的研究结果.

This article introduces the process and skills of bituminous emulsion production, discussing the methods and features of the hardware and software of 8098 chip computer which is used in measurement and control system for bituminous emulsion production procedure.

介绍了乳化沥青的生产工艺及过程，较详细讨论了8098单片机在乳化沥青生产中测控系统的硬件设计和软件设计的方法及特点。

Put forward rational improvement proposals on production procedure, quality, cost reduction, etc.

能够针对生产流程 、 质量及成本节约等方面提出合理化的改进建议.

The production procedure of polyvinyl acetate latex paint in polyvinyl formal solution was studied.

研究了在聚乙烯醇缩甲醛溶液中制备聚醋酸乙烯酯乳胶漆的方法.

First steep corn powder in dilute sulfite liquor, then produce starch syrup by routine production procedure.

先用稀亚硫酸溶液浸泡玉米粉, 再用常规操作生产淀粉糖浆工艺.

Traditional production procedure totally depends on human operations, thus exists lots of shortcomings during production, such as product and time loss caused by negligence and slow information collection.

传统的生产流程完全人工控制，在生产的过程中存在着诸多缺点，例如由于疏忽导致的生产损失和时间损失，必要信息的收集速度缓慢等。

vegetable cleaning is the essential work procedure to vegetable processing and cleaned vegetable production.

蔬菜清洗是蔬菜加工和净菜生产中必不可少的工序之一。

At the same time, he also refines the key points for the production quality test of the different types of Ex product in the steps of purchasing acceptance, procedure inspection, product inspection, and so on.

同时还对防爆电气产品的采购验证、过程检验、成品检验以及不同防爆类型的产品质量检验要点进行了介绍。

Thermoplastic material is a kind of high scientific and technologic product in wide use, while irradiation is the key procedure in thermoplastic production.

热缩材料是用途广泛的高科技产品，辐照是生产热缩材料的关键工序。

The influential factors on propylene chlorohydrin yield in the key procedure of chlorohydrination of propylene oxide production by chlorohydrination are discussed and analysed ( qualitatively), and the countermeasures of optimum control are raised to increase the yield of propylene chlorohydrin.

根据反应原理并结合生产实践，定性分析、探讨了氯醇法生产环氧丙烷的关键工序&氯醇化工序中影响氯丙醇收率的因素，提出了提高氯丙醇收率的优化控制措施。

The influence of pipe forming process, welding procedure and electric system variation on the occurence of porosity in weld Was studied. Then a good condition to get ride of porosity in production line for spiral FiFe welding is created.

本文研究了钢管成型工艺、焊接工艺和电气系统等方面对螺旋焊管气孔产生的影响，从而为焊管生产创造了良好条件。

In order to stop and prevent quality issue on production line effectively and reduce quality cost, it provides 6 methods that include stop line procedure used rightly, temporary control point set up on line, product grouping, etc.

为了及时制止质量问题的扩展、预防质量问题的发生及降低质量成本，本文提供了正确使用停线程序、设立临时控制点、产品分组等6种有效方法。

It comes from the facts that 80% of manufacturing costs are generated in the technical production preparation stage, especially in the procedure of mold design and technological process preparation.

在注塑模具开发过程中，80%的制造成本出自生产技术准备阶段，特别是在模具的设计和工艺准备阶段。