program diagram的例句大全

In the end, a program diagram of IPC of larch bark beetle occured in larch plantation was presented.

提出了适于人工林落叶松八齿小蠹防治的IPC程序图。

As an example, the counting results produced by the program is processed, and the comparison diagram of theoretical frequency and experimental frequency is obtained, which can be used in χ 2 checking.

最后根据程序生成的模拟计数进行了处理，获得了理论频数和实验频数的对照图；进一步可以进行x2检验。

In addition, the post-processing program can also plot the normal force diagram, the shearing force diagram and the bending moment diagram of the frame beam and column.

此外，该后处理程序还可以绘制框支梁柱的轴力图、剪力图、弯矩图。

This paper discusses the working principle, composition and program block diagram of the terminal device.

文章阐述了该终端机的原理、构和程序框图。

Program design and its application for drawing ternary phase diagram

三元相图绘制编程与应用

A scheme for designing the three-position switch with both analog and digital devices is presented with specific diagram and program code.

介绍了一种利用模拟可编程器件和数字可编程器件设计三工位开关控制器的方案，并给出了具体的电路图和程序代码。

Through analysis, the authors draw a cause and effect feedback chart to which the authors give flow diagram explanation. Besides, the authors work out the emulation program of industry sub pattern by using the special purpose language of systematic dynamics, DYNAMO language.

通过分析，绘制了工业子模型的因果反馈图，并进行了流图分析，据此采用系统动力学专用语言DYNAMO语言，编写工业子模型仿真程序。

By skillful application of timing sequence diagram in programming and program analysis, the programming of PLAC could be faster.

通过时序图在编程和程序分析中的巧妙应用，可使PLC的编程更加快速。

In this paper, the designing method and work theory of IP telephone are introduced especially. At the same time the circuit diagram and main program design frame are presented.

文中着重介绍了IP电话的实现方法和低功耗电路设计思想，给出了IP电话机的整体框图和部分电路图以及主程序设计框图。

In this paper, MATLAB software is used to work out the computer program for solving the two-rank differential equations which describe the nonlinear capture of the two-rank PLL. The computer then draws automatically the phase trajectory and time response diagram.

采用MATLAB软件，编制了求解描述二阶PLL非线性捕获的二阶非线性微分方程的程序，计算机自动绘制了相轨迹和时间响应图；

At the same time design data flow diagram for program development for reference.

同时设计数据流程图，用以程序开发参考。

Attention are mainly focused on the modular design of PLC program, flow figure of each subsystem, the assignment of the program function block, the communication principle between PLC and up-lever computer and the timing sequence diagram.

着重介绍了PLC程序的模块化设计以及各个工位的程序流程、程序功能块的划分以及与上位机通讯的基本原理和时序图；

This article introduces a new method of the realization of the Serial Port SoftDog based on MCU. And its electric circuit diagram, MCU source program and VB source program have been given out at the same time.

介绍一种新的基于单片机的串口软件狗的实现方法，并给出了其电路原理图、单片机源程序及检测软件狗的VB参考程序。

UML ( unified modeling language) technologies were used to construct the conceptual class diagram of the agent. The design methods of formalization expression and general agent program were given. The implementation mechanism of integrated scheduling engine and concurrent message processing was expatiated.

采用UML技术设计Agent的概念类图，给出了Agent的形式化表达和通用程序的设计方法，并阐述了综合调度引擎、并发性消息处理的实现机制。

This paper describes the teletext receiver developed in accordance with the Chinese Broadcast Teletext Specification ( WG& 84), the processing method of the multiplex data and the main program block diagram.

本文给出了一种按我国电视文字广播试验规范（WG&84）研制的接收机的构成、多工信号处理方法及主要程序流程。

The bending moment diagram of plane bar structure is plotted by using VBA on AutoCAD 2000 after the bending moment has been computed with Matrix Displacement Method Program. The making of the bending moment diagram under three element loads is described.

用VBA技术在AutoCAD2000下绘制矩阵位移法计算后的平面杆系结构的弯矩图，描述了三种单元荷载作用下的弯矩图的生成。

The hardware includes parts selection, terminal I/ O distribution and wiring diagram. The software program includes control software design and procedures.

文章对系统的软硬件都进行了设计，硬件设计包括系统各部分选型、端子的I/O分配、接线图等；软件设计包括控制主程序以及位控程序设计。

The author presents a method to test whether Series MCS 51 Simulator occupies the hardware resource of chip computer prototype, and the relative hardware diagram and program list are presented in this paper.

对MCS&51系列单片机仿真器是否占用单片机样机的硬件资源提供了一种测试方法，并给出了相应的硬件图及程序清单。

Gives the flow diagram of main program and improved algorithm.

给出了主程序流程和改进算法的具体流程。

The program flow diagram and experimental results are shown.

最后，给出了程序框图及实验结果。