radius of bending的例句大全

influence of wall thickness deformation upon the minimum bending radius of bending tube

壁厚变形对弯管最小相对弯曲半径的影响

By analyzing the wide sheet bending, the variations of theoretic radius values of outer surface, sheet thickness and thinned coefficient with radius of inner surface in bending were put forward. The results were compared with testing data and approximate values.

对宽板弯曲变形过程进行分析，提出了弯曲过程中板坯外表面半径，板料厚度和变薄系数随板坯内表面半径变化的理论解，并与查表法和近似解作了比较。

The biomechanical properties of the healing radius were analyzed by a three point bending test.

桡骨的生物力学性能由三点弯曲实验所得的结果进行分析；

To study the equivalent thickness, and effects of superposition throttle slices to damper characteristics, the bending deformation is analyzed at the throttle mouth radius r_k, and the equivalent thickness formula deduced.

为了探究减振器叠加阀片等效厚度、设计方法及其对减振器特性的影响，对节流阀片在阀口位置的弯曲变形量和叠加阀片等效厚度进行了研究，给出了等效厚度计算公式。

The determination of the minimum bending radius in the design of the pipe_bending die was stated. And the structure of the die slot, the form and installation of the shaft core were introduced. The pipe was prevented effectively from deformation.

叙述了弯管模设计中最小弯曲半径的确定，弯管模模槽的结构，芯轴的形式和安装，有效地防止管子变形，并通过实践经验给出了一些模具设计参数。

The springback of wide metal sheet after large radius pure bending

宽板大曲率半径纯弯曲回弹量理论分析

In the NC bending process of thin-walled tube with small bending radius, the maximal hoop strain can reach 1/ 3 of the tangential strain and can not be neglected.

薄壁管小弯曲半径数控弯曲成形中，周向应变不可忽略，其值最大可达最大切向应变的1/3；

testing of fibre optic elements; determination of the minimum bending radius of optical fibres

光纤件的检验.光纤最小弯曲半径的测定

permissible bending radius: not less than 6 times of overall diameter for unarmored cable ;

推荐允许弯曲半径：无铠装层电缆应不小于电缆外径的6倍；

bending analysis on drilling string in whipstock of ultrashort turning-radius horizontal well

径向水平井造斜器内钻杆的弯曲状态分析

the design and construction of prestressed bending beam with minor radius

预应力小半径弯梁的设计与施工

discussion about calculation methods of the minimum relative bending radius for plate bending

板材弯曲最小相对弯曲半径计算方法探讨

Tube bending is a process by which a straight piece of tube is formed to a selected radius and angle of bend.

弯管工艺是指将平直的管子按选定的半径和弯曲角度弯曲成形。

feature: anti-bending of hose body, small bending radius, good stiffness, with or without metal fittings available.

特性: 管体耐曲挠 、 弯曲半径小 、 挺性好.带或不带金属接头.

the minimum bending radius should not be less than 10 times of cable diameter.

电缆弯曲半径应不小于电缆直径的10倍.

the minimum bending radius is 25 times of the diameter of the cable.

产品的最小弯曲半径为电缆直径的25倍.

the bending radius should not be less than 25 times of the cable diameter.

电缆弯曲半径:不小于电缆外径的25倍.

bending radius of the cable on less than 10 times of short axis diameter.

电缆弯曲半径不小于电缆短轴尺寸的10倍.

Under the conditions of the same internal pressure, with the relative bending radius increased, ellipticity and the thickening rate of internal measuring point decreased; the thickening rate of outer measuring point gradually were also decreased.

在充液压力相同的条件下，随着相对弯曲半径的增加，椭圆度逐渐减小；内侧点的增厚率逐渐减小；外侧点的减薄率逐渐减小。

the minimum bending radius should be 15 times of the outer diameter.

电缆最小弯曲半径为电缆外径的15倍.