reactor shell的例句大全

Meanwhile the article introduced the installation technique of the Johnson Net made in China and the technique of cutting, welding and heat treating of reactor shell.

同时介绍了大型国产约翰逊网的安装技术，以及SA387Gr11CL2材质的反应器壳体的切割、组对、焊接和热处理技术。

The strength and equivalent stress of the remainder wall thickness of reactor shell under new working condition were checked.

对反应器壳体剩余壁厚在新工况条件下的强度和当量应力进行了校核；

The corrosion and temper embrittlement of reactor shell probably occured under hot wall condition were analyzed.

对反应器壳体在热壁条件下可能发生的腐蚀和回火脆性进行了分析。

This paper discussed various technology of urea reactor shell lining, emphatically expound the detail of hot sleeving liner process.

本文对尿素合成塔筒体衬里的各种工艺方法进行了探讨，着重阐述了热套衬里工艺的详细过程。

The anode polarization curve of A0 pure aluminum in DI ( de-ions) water was measured to simulate the pit corrosion of reactor pool shell.

测量A0纯铝在去离子水中的极化曲线用来模拟反应堆池壳的点蚀。

For box-type reactor complex thin-walled shell structure, the finite element method is used to carry out its strength and displacement analysis.

针对电抗器箱体类的复杂薄壁板壳结构，一般采用有限元法对其进行强度校和以及位移分析。

Starting Characteristic of UASB Reactor by Adding Oyster Shell Powder

牡蛎壳粉末投加UASB反应器的启动特性

Mathematical simulation and operating conditions analysis of Lurgi methanol synthesis reactor(ⅰ) lurgi tube-shell type methanol synthesis reactor

鲁奇甲醇生产装置数学模拟和工况分析&（Ⅰ）鲁奇副产蒸汽管壳型甲醇合成塔

High pressure reactor's overall water pressure test was used to bulge lining plastic deformation, then eliminate the gap between lining and shell.

水压胀合法是利用高压釜整体水压试验时的压力来胀合衬里，使衬里产生塑性流动，达到全部或部分消除衬里与壳体之间的初始间隙。

In order to make the catalyst of propane catalytic dehydrogenation perfect, a special hard-wearing core-shell dehydrogenation catalyst is put forward and designed aimed at the problem of serious abrasion in fluidized-bed reactor. 4.

为了进一步完善丙烷催化脱氢催化剂，本文还针对催化剂在流化床反应器内磨损严重的问题，提出并设计了独特的耐磨核壳式脱氢催化剂，结果表明催化剂的磨损指数显著降低。

The Buckling Analysis for Thin Shell Structure of Flow Course in Ethyl-Benzene Dehydrogenation Reactor

乙苯脱氢反应器薄壳流道结构的稳定性分析

According to the equipment working condition, the shell of oxidative dehydrogenation reactor should select American SA240-304H steel plate.

按设备工况，氧化脱氢反应器壳体应选用美国的SA240&304H钢板。

The plan is to build a110-metre-high ( 360-foot) shell over Chernobyl's No4 reactor, which blew up after a safety experiment went wrong.

计划准备在切尔诺贝利4号反应堆上建设一个高110米的外壳，其因安全试验出错，引发爆炸。

The one-dimensional model of Lurgi tude-shell type methanol synthesis reactor has been established.

建立了鲁奇式甲醇合成塔完整的双速率一维模型.

Property Test for Shell Longitudinal Weld Shaping of HTR-10 Reactor Pressure Vessel

HTR-10反应堆压力容器筒体纵缝成形性能试验

The existing problems of shell side structure for domestic current tubular fixed bed reactor are discussed and evaluated. The improvement of shell side structure by adopting outside flow deflector type inlet and outlet structure and adopting baffle rod to support reaction tube are proposed.

探讨和评介了国内现行列管式固定床反应器的壳程结构存在的问题，提出壳程采用外导流筒式进、出口结构和采用折流杆支撑反应管的结构改进措施。

Mathematical Modeling and Comparison of Lurgi Tube-shell Type Methanol Reactor with by-Product Steam and I.C.I. Four Stage Quench Type Methanol Synthesis Reactor II. Mathematical modeling and optimization of four stage methanol synthesis reactor

鲁奇副产蒸汽管壳型和I.C.I.四段冷激式甲醇合成塔的数学模拟和比较Ⅱ、四段原料气冷激甲醇合成塔的数学模拟及最佳化

Experimentally, white pine sawdust and peanut shell selected as typical farming and forestry waste were analysed on the fluid bed reactor with orthogonal experiment method to analyse effect of multi-factors on pyrolysis liquid yield rates ( LYR), and then optimized pyrolysis craft.

试验上，利用改进后的流化床装置结合正交试验手段研究多因素对典型的农林废弃物白松木屑和花生壳粉热解液体产率的影响，进而优化热解工艺。

Bridge, crane beam, sleeper, ocean structure, pressure institution and nuclear reactor safety shell are often endured stress from many circle times and biggish repetition loading, and fatigue collapse is very easy accrued because of long and repeating loading.

桥梁、吊车梁、轨枕、海洋结构、压力机构和核反应堆安全壳等经常承受循环次数较多而重复荷载较大的结构，在长期的反复荷载的作用下极容易发生疲劳破坏。