relative deformation的例句大全

The deformations in the contact slice of the model consist of two parts i.e. shear deformation and sliding deformation. For the normal constructive model, the nonlinear model between the normal stress and normal relative deformation was adopted.

该模型将接触带内的变形分为剪切变形与错动变形两部分，对于法线方向采用法向应力与法向相对变形之间的非线性模型。

And there is a relation between relative deformation of test specimen and its confinement.

试件的相对变形量与其约束状况有一定的关系，不对称约束可能会使试件在低温下的相对变形量增大。

Through a lot of test pile material, this essay concludes the vertical bearing capacity calculation formula of man-made pile with bulb shaped base by strength theory and relative deformation as control criterion.

本文通过大量试桩资料和有限元计算分析，给出了以强度理论和相对变形为控制标准的人工挖孔扩底桩竖向承载力计算公式。

Research conclusion: The relative position between tunnel and sliding plane is the major cause to determine the deformation features of tunnel;

研究结论：（1）隧道与滑面的相对位置关系是决定隧道变形特征的主要因素；

The pulling displacement of the anchor bolt is broken down into the elastic deformation of the free segment, the tensile deformation of the anchored segment and the relative shear displacement between the bolt and soil.

将锚杆拉拔位移分解成自由段的弹性变形、锚固段的拉伸变形和锚固段与土体之间的相对剪切位移。

Relationship has been studied on defect to deformation degree, friction factor and relative length of mould plastic section.

同时，研究了表面缺陷产生与变形程度、擦因数及模具整形段相对长度的关系。

We quantitatively analyze the casing damage, present the deformation of casing with the change of relative position of stratum and study the angle of inclination of stratum, the pressure of stratum, the size of soaked area and the hydration of marl.

以地层的相对错动表示套损变形情况，研究了地层倾角、地层压力、浸水域大小和泥岩水化情况改变对套损的影响。

GPS relative positioning technique was used in Shuichang open pit mine to monitor deformation of its high steep slopes.

水厂露天铁矿采用GPS静态相对定位技术对其高陡边坡变形进行了监测。

The short wave and transversal wave of deformation of deck system, the absolute and relative displacements, and the transfer approach between them are also presented and expounded.

提出了同一线两轨3m内相对变形量的物理意义及计算方法，提出和阐述了桥面变形的短波效应和横波效应、绝对位移和相对位移及相互间的转换方法。

The porosity defect is that in certain area inside the cast ingot exist small cellular voids relatively equally distributed, slight difference in mechanical properties, obvious plastic volume deformation and variation of relative density governed by the spherical stress tensor.

疏松缺陷是一定区域上相对均匀分布着的蜂窝状小空洞，疏松区域上各处的力学性能相差小，表现为明显体积塑性变形，材料的相对密度变化主要依赖于应力球张量。

marc software, and studied effect of the relative density on the deformation mechanism, yield strength, strain platform and energy-absorption of the metal honeycomb.

Marc有限元分析软件对其进行有限元模拟分析，比较研究了相对密度对蜂窝材料的变形机制、屈服强度、平台应变及能量吸收性能的影响。

Combining with the relative movement parameters, a deformation analysis method of successive approximations is presented.

结合相对运动参数, 提出了一种逐渐趋近的变形分析方法.

The hull deformation will change relative position of bearing chock, thereby change the support state of bearing.

船体变形会引起轴承座相对位置的变化，进而引起轴系轴承支撑状态发生改变。

At the same time of making relative measurement, the absolute position of ( reference) point is measured with common measuring method and from which the absolute amount of deformation of ( plasmodium) can be derived.

在进行相对测量的同时，用常规测量方法测定参照点的绝对位置，并由此来推求变形体的绝对变形量。

Monitoring Absolute Amount of Deformation with Relative Displacement Method

绝对变形量的相对位移法监测

During 1985~ 1992, the deformation field tendency dog leg had been notable weakened vertical differential movement may be seismogenic zone that is in the relative blocking stage for seismogenic energy accumulation to definite extent.

而1985～1992年形变场趋势转折与垂直差异运动显著减弱，可能意味着孕震能量积累到一定程度后，孕震区处于相对闭锁阶段。

the limit deformation extent can be described by the minimum relative bending radius.

板料弯曲时的极限变形程度可用最小相对弯曲半径来描述.

On the base of relative data of the maximal deformation, studied the factors that effect the deformation of reflector surface of small telescope with bottom support.

在取得的相互关联的最大镜面变形数据基础上，研究了影响小口径反射镜底支承镜面变形的因素。

Fractional softening evaluated from yield stress as well as relative peak stress and peak strain was measured against holding time after hot deformation.

调查了由两次加载拉伸变形时的屈服应力求得的静态软化率以及相对峰值应力比和峰值应变比随等温保持时间的变化。