ring method的例句大全

At the same time, the reaction yield is high, and also proved that the method has universal applicability. 1,3-dipolar cycloaddition is the best way to build the isoxazole ring.

同时，反应的产率很高，也证明了该方法具有很好的普遍适用性。1,3-偶极环加成是构建异嗯唑环的最好方法。

Field corrosion monitoring of rebars in concrete by guard ring electrode method

基于护环技术的混凝土中钢筋腐蚀监测研究

By means of finite element method, this paper carried out a statics analysis on the complete appliance of three-ring reducer. The reacting force of each structural member and the variation law of Von Mises stress were obtained during one period running of the three-ring reducer.

通过有限单元法，对三环减速器的整机进行了静力学分析，得到了三环减速器运转一个周期时，各个构件的作用反力和VON MISES应力变化规律。

The Method of Machining Spherical Surface of Outer Guide Ring for Tubular Turbine

贯流式水轮机外导水环球面的加工

A new intuitional diagram, spiral ring, is obtained by this method and its attributes were studied.

并得到一种新的直观图&螺旋环，研究了螺旋环的性质；

This paper introduced principle, process, characteristics and controlling deep slot of spiral groove movable ring of photoetching in the liquid hydrodynamic seal. The new method of high-energy ions etching spiral groove movable ring was put forward.

主要介绍了流体动力密封螺旋槽动环光刻工艺的特点、原理、工艺过程、工艺流程、槽深控制方法以及应用情况，提出了采用高能束流刻蚀螺旋槽动环的新途径。

Original construction method of concrete ring wall of large scale storage tank often has some problems such as big deformation and spacing deviation of reinforcing steel bars, being difficult to control ring wall curvature and low primary formation rate.

以往大型储罐基础混凝土环墙施工极易存在钢筋变形大，间距偏差大，混凝土环墙曲率难以控制，一次成型率低等问题。

This paper focuses on electric design and test method of the slip ring.

本文着重介绍视频汇流环的电器设计和它的测试方法。

According to the related theory and combining with microscopic method, the friction and wear mechanism of contact materials for the conductive slip ring was analyzed.

最后根据电接触摩擦磨损的相关理论，结合微观手段，分析了导电滑环接触材料的摩擦磨损机制。

A predicting method of pressure loss in realistic annulus DS ring

预测实际环空中压降的方法

Lateral Mass Method with Side Trapezoid Thread Ring Pitch Diameter Evaluation of Uncertainty in Measurement

侧规法测梯形螺纹环规中径测量结果的不确定度评定

New Method of Measuring Piston Ring End Gap Clearance with line Matrix CCD

线阵CCD检测活塞环闭口间隙的新方法

Method of separating parameters design for ring dye laser resonator

环形染料激光腔的分离参数设计方法

The method of measuring the temperature of the discharge gas in He-Ne ring laser by thermal image instrument was proposed in this paper, The result was gained by experiment and calculation.

本文提出了用热像仪测量He Ne气体环形激光器放电管内气体温度的方法，并通过实验和计算得出了结果。

Error analysis and CNC machining method for holes on large diameter ring workpiece

大直径环形件孔系误差分析及数控加工方法

On load carrying capacities of ring plates under Mises yield condition by using the method of weighted residuals

用加权残数法求环板在Mises屈服条件下的极限载荷

Method of Prolonging the Service Life of Piston Ring in Air Compressor

延长空压机活塞环使用寿命的方法

By using method of ring and semi-group theory and by widening the satisfactory conditions of the subsemiring of semiring, the concept of weak pseudo ideal of semiring is introduced.

借助环论与半群理论的思想方法通过对半环的子半环的条件进行加强，提出了半环的弱伪理想的概念。

Design calculation of dual semi-ring ( DSR) high pressure vessel is introduced in this paper. It uses the method of stress analysis based on the theory of shells.

介绍了双合环高压容器的设计计算，它应用基于壳体理论的应力分析方法。

Analysis of grinding method for bearing ring with double grooves

双沟轴承套圈沟道磨加工方法浅析