roller mill的例句大全

The paper describes roller mill about its structure and working principle, makes analysis and determination to optimization of such parameters as pull-in angle for material, diameter of cylinder, diameter of roller and average granularity for feeding.

阐述了辊筒磨的结构和工作原理，并对辊筒磨的物料拉入角、筒体直径、磨辊直径以及入料平均粒度等结构参数进行了优化分析和确定。

In view of the low capacity of ball mill, GM1000 × 200 high pressure roller mill was used to pretreat the feed to the ball mill at Gushan Iron Mine.

马钢姑山铁矿针对球磨机处理能力低的问题，采用GM1000×200型高压辊磨机对球磨机给矿进行预处理。

Energy Saving and Producing Non-metallic Minerals Powder by Vertical Roller mill

立式磨在非矿粉体加工中的应用及其节能探讨

It is very difficult for traditional mechanical air lock feeder to meet the demands of locking the air in the high negative pressure system of a roller mill because of problems existed in its principle, structure and function.

传统的机械式锁风喂料装置由于在原理、结构和功能等方面的问题，难以满足立式磨机强负压系统的锁风要求。

the semi-industrial test on fine products by meishan dressing plant was carried out with the rp80/ 25 type high pressure roller mill produced by homburg corporation of germany.

采用德国洪堡公司的RP80/25型高压辊磨机对梅山选矿厂细碎产品进行了半工业试验，研究了能耗、水分、通过量及循环负荷等因素对辊压效果的影响。

finish cement grinding by horizontal roller mill

浅谈卧式辊磨水泥终粉磨技术

SBS plastic roller mill work into cutting disks.

SBS塑料磨粉机工作部分为刀盘。

This model analyze the effects on the strip gauge when some factors vary in the course of rolling such as entrance thickness of strip, control tankage in the backpressure cavity of hydrocylinder, ordinance of strip, roller eccentricity, stiffness coefficient of rolling mill and nonlinear factor.

该模型分析了轧制过程中的诸因素如：带钢入口厚度、液压背压腔控制容积、轧件规格、轧辊偏心、轧机纵向刚度、非线性因素等对带钢精度的影响。

Making use of the technology to monitor and diagnose the key equipment of high speed wire rod rolling mill, such as finish rolling unit, triple increase gear, gripping roller and wire spinning machine, the satisfied effect is reached.

运用该技术对高速线材轧机设备中的精轧机组、三重式增速箱、夹送辊及吐丝机等关键设备进行监测及诊断，取得较满意的效果。

The Reason Analysis of Influencing Abrasion Resistance of Sugar Cane Mill Roller

甘蔗压榨机榨辊耐磨性低的原因分析

analysis of the structure and strength for cross universal coupling used at roller end of 3500 mill

3500轧机辊端联轴器结构与强度分析

The paper involves an investigation into the new steel pipe manufacture technology of roller die drawing with the two-stand Y type three-high mill.

研究了利用二连式Y型三辊辊模拉拔钢管生产新技术。

quite good effect is gained from broadening the angle of entry of the piercing mill and narrowing the angle of departure of the roller, by which the efficiency of piercing is increased and per unit energy consumption is reduced.

通过增大穿孔机送进角，减小轧辊出口锥角，从而提高了穿孔效率，降低了单位能耗，收到了较好的效果。

GA-Based Cluster Fuzzy Controller for a Four Roller Cold Rolling Mill

基于遗传算法的四辊可逆冷轧机恒张力聚类模糊控制器

The Analysis on the Stability of Working State of Hot Rolling Mill with Four Rollers which Produce Broads and Strips Driven by Working Roller

工作辊驱动四辊热轧板带轧机工作稳定性分析

Analysis and Research on Mechanism of Roller System in Aluminium Foil Mill

铝箔轧机辊系机构分析与研究

Study of Backup Roll Contour Optimization for Cold Strip Temper Rolling Mill Demonstration of the Static and Dynamic Balance of the Roller in Heavy-duty Roller

冷轧带钢平整机支撑辊辊型优化技术的研究重型轧机辊道辊静动平衡优化工艺论证

Analysis of Contact Stress between Vertical Roller Shaft and Hole of Vertical Roller Chock in Universal Mill

万能钢梁轧机立轧辊轴与轴承座孔接触应力分析

In our one-heating forming reform, a new king of roller conveyor-stepping roller conveyor is designed as back conveyor to replace the using elevator ( or two-layer roller conveyor) in three-roller rolling mill to reduce the drawbacks in present application.

针对目前一火成材改造中三辊轧机机后辊道采用升降台（或双层辊道）所存在的缺陷与不足，采用一种新型的阶梯辊道设计来取代现有辊道。

A mathematic model of the optimization to take aim at the optimum dynamic balance has been built. The three-roller cold tube-rolling mill on the LDD-12 four-strands has been calculated using the direct-scouting Complex Method.

建立了以最佳动平衡为目标的优化教学模型，并用复合形法对LDD-12四线三辊冷轧管机进行了实算。