roller mill的例句大全

Study of Backup Roll Contour Optimization for Cold Strip Temper Rolling Mill Demonstration of the Static and Dynamic Balance of the Roller in Heavy-duty Roller

冷轧带钢平整机支撑辊辊型优化技术的研究重型轧机辊道辊静动平衡优化工艺论证

The roller stand, as the central part of tension reducing mill of seamless steel tube finish rolling line imported from Germany is the key consumable part of mills.

从德国引进的无缝钢管精轧生产线，其张力减径部分中心部件轧辊支架是机组中的主要消耗零件。

Analysing Reason for Excess Tension of Six-Roller Sheet Rolling Mill Using FEM

六辊冷连轧机张力超调成因的有限元分析

Analysis and Research on Mechanism of Roller System in Aluminium Foil Mill

铝箔轧机辊系机构分析与研究

The paper involves an investigation into the new steel pipe manufacture technology of roller die drawing with the two-stand Y type three-high mill.

研究了利用二连式Y型三辊辊模拉拔钢管生产新技术。

Drive characteristics and rectiformer choosing method of 1 450 mm six-roller reversing cold-rolling mill train are described. Calculation and choosing method of some important parameters of rectiformer and reactor, such as voltage, capacity, short circuit impedance and inductance are given.

介绍了1450mm六辊可逆冷轧机组的传动特点和整流变压器的选用，并给出了整流变压器及进线电抗器的重要参数电压、容量、短路阻抗及电感量等的计算和选用方法。

Analysis of Contact Stress between Vertical Roller Shaft and Hole of Vertical Roller Chock in Universal Mill

万能钢梁轧机立轧辊轴与轴承座孔接触应力分析

Analysis to the Motion of the Main Shaft System in the Vertical Mill with Sus-pended Roller

立式悬辊磨主轴系统运动分析

Analysis about Fatigue Failure of Working Roller in Aluminium Foil Mill

铝箔轧机工作辊疲劳破裂浅析

N this paper, the load distribution of the 4-row cylindrical roller bearing on the mill has been calculated with finite element method, In the calculation, the bend deformations in the chocks and bearing external rings have been considered.

对轧机常用的四列短圆柱轴承的负荷分布进行了有限元计算，在计算中考虑了轴承座和轴承外圈的弯曲变形，并在此基础上对轴承进行了寿命分析。

The Analysis on the Stability of Working State of Hot Rolling Mill with Four Rollers which Produce Broads and Strips Driven by Working Roller

工作辊驱动四辊热轧板带轧机工作稳定性分析

GA-Based Cluster Fuzzy Controller for a Four Roller Cold Rolling Mill

基于遗传算法的四辊可逆冷轧机恒张力聚类模糊控制器

quite good effect is gained from broadening the angle of entry of the piercing mill and narrowing the angle of departure of the roller, by which the efficiency of piercing is increased and per unit energy consumption is reduced.

通过增大穿孔机送进角，减小轧辊出口锥角，从而提高了穿孔效率，降低了单位能耗，收到了较好的效果。

analysis of the structure and strength for cross universal coupling used at roller end of 3500 mill

3500轧机辊端联轴器结构与强度分析

The Reason Analysis of Influencing Abrasion Resistance of Sugar Cane Mill Roller

甘蔗压榨机榨辊耐磨性低的原因分析

Making use of the technology to monitor and diagnose the key equipment of high speed wire rod rolling mill, such as finish rolling unit, triple increase gear, gripping roller and wire spinning machine, the satisfied effect is reached.

运用该技术对高速线材轧机设备中的精轧机组、三重式增速箱、夹送辊及吐丝机等关键设备进行监测及诊断，取得较满意的效果。

This model analyze the effects on the strip gauge when some factors vary in the course of rolling such as entrance thickness of strip, control tankage in the backpressure cavity of hydrocylinder, ordinance of strip, roller eccentricity, stiffness coefficient of rolling mill and nonlinear factor.

该模型分析了轧制过程中的诸因素如：带钢入口厚度、液压背压腔控制容积、轧件规格、轧辊偏心、轧机纵向刚度、非线性因素等对带钢精度的影响。

Prototype of designing edge curves of formed bits for mill roller is composed by three important parts: subsection parameter inputting part, uniform parameter inputting part and executing windows. Standard G code document supports a fine interface for the three parts.

轧辊成形刀片刃形设计原型系统由分段参数输入模块、整体参数输入模块、运行窗口模块组成，标准的G代码文件是三个模块的接口，并且在VCNC系统中进行了验证。

Design Method for Central Feeding of Three-roller Vertical Mill

中心进料三辊立磨的设计方法

Characteristics of Taped Leaf Spring and Design of Three-roller Pattern Mill

变截面板簧的特征与三辊模板式轧机的研制