rolling direction的例句大全

The accurate calculation of stress field based on EHL theory and theory of elasticity showed that the shear stresses at surface in direction of 30 ° with rolling direction cause the pitting cracks and the tensile stresses accelerate the crack growth.

结果表明：预加拉应力使裂纹起源于表面的点蚀寿命缩短，与滚动方向成30°角的剪应力是引起点蚀的决定应力。

The average radial clearance, body clearance diameter of the external channels and rolling direction.

平均径向间隙, 外部渠道和全身清除直径轧制方向.

If you are reinstalling the old drive belt, it is absolutely necessary to observe the previously marked rolling direction.

如果安装旧的传动带，请务必遵照先前标记的滚动方向。

Prominent in the raceway surface and rolling direction parallel to the narrow shroud.

突出于滚道表面与滚动方向平行的窄凸肩.

Rolling direction perpendicular to the plane of the bus for the straight line roller.

在垂直于滚动方向的平面内的母线为直线的滚道.

The rolling direction of the timing chain must always be the same.

正时链条的滚动方向必须始终相同。

The acoustic emission characteristics reflect the macroscopic properties along rolling direction of high strength aluminum alloy.

高强度铝合金沿晶界断裂过程中的声发射信号特征反映了材料沿轧制方向的宏观性能。

The evident effect of rolling direction on fracture toughness is found.

发现板材的轧制方向对断裂韧性影响显著，LT方向试件的断裂韧性远超过TL方向试件的断裂韧性。

Pay attention to rolling direction of previously used belts.

注意先前使用的皮带的滚动方向。

Camshaft roller-type chain; pay attention to rolling direction.

凸轮轴滚筒链条；注意滚动方向。

When Zircaloy-4 is rolled along rolling direction of original plate, ft is larger than fl, which can be explained by the activation of {` 1010} slip system in some crystals.

沿原始板材的轧向进行轧制时，部分晶粒中的{`1010}柱面滑移开动，使轧制后的ft大于fl；

Never turn the crankshaft against the rolling direction or when the chain tensioner is removed.

在链条张紧器拆除的情况下，切勿逆转动方向转动曲轴。

The density center of basal pole rotates away by about 18 ° from the transverse direction of sheet to rolling direction;

冷轧后的基极密度中心围绕板横向向轧制方向旋转约18°；

theoretical direction may be provided on judging defect of rolling workpiece surface.

从而为估测楔横轧成形阶梯轴类件时轧件表面是否会产生缺陷提供理论指导.

The constituent, working principle of AGC system and the spring curve of rolling mill were introduced. The reasons for variation of thickness deviation in longitudinal direction were analyzed in detail, and the corresponding solutions were put forword.

介绍了液压AGC控制系统的组成、工作原理及轧机的弹跳曲线，详细分析了带材在纵方向上造成厚差波动的原因，并提出解决方案。

Perform the eye stretch exercise by looking up toward your eyebrow and rolling your eyes around in a circular motion as far as they can in each direction.

眼睛向眉毛的方向向上看，然后以环形运动转动向各个方向转动。

Experimental results show that: texture division resulting from shear stress applied on the cross shear area can be eliminated in a double direction rolling process, and favorable deformation texture better than that of conventional rolled sheel may be obtained;

结果表明：双向轧制能有效地消除剪切应力导致织构组分偏离的影响，并获得比常规轧制板材更为理想的冷轧织构组态；

But now she is on her own," with no direction home, like a complete unknown, like a rolling stone."

但是现在，她独自一人，“没有家的方向，孤零零，像一个滚石。”

How does it feel how does it feel to be on your own with no direction home like a complete unknown like a rolling stone?

孤身一人的滋味你觉得怎么样？没了回家的方向、也没人认识像块孤零零的石头子？

The former is similar to bulge, but the deforming mode of the latter is rolling in which the stress is tensile in generatrix direction and the wall thickness are mainly reduced in this zone.

前者的受力情况类似于胀形，后者为母线方向拉应力作用下的辗压变形，该区起主要减薄壁厚的作用。