rolling process的例句大全

Thermo-mechanical Coupling Analysis of Continuous Cast Rolling Process Using MARC Software

基于MARC平台的连续铸轧热力耦合分析

The main program and subroutines are programmed in C language. Thermo-mechanical Coupled Analysis of Continuous Cast Rolling Process Using MARC Subroutines

测试单元所用主程序及子程序均采用C语言编制。基于MARC二次开发的连续铸轧热力耦合分析

A rigid pushing model based-on 3D thermo-mechanical coupled analysis with FEM was used to simulate wire and rod multi-pass continuous rolling process.

基于三维热-机耦合有限元分析方法建立了刚性体推动模型，模拟棒线材多道次连轧过程。

Test results of lead work-pieces verify the feasibility of rolling process and die design.

铅试件辗压试验结果证明辗压成形工艺和模具设计的可行性；

To unite with manufacture practice, the optimization method of the dynamic programming law in the groove design of bar and wire stock was investigated. A set of computer software aiming at minimum energy consumption was offered for high-speed rolling process of the bar and wire stock.

结合生产实际，研究了动态规划法在棒、线材孔型设计中的优化方法，为高速线、棒材生产提供了一套以低能耗为目标的计算机优化软件。

Development of the Mass Flow Simulation System of Thin Slab Continuous Cas-ting and Rolling Process

薄板坯连铸连轧流程物流仿真系统的开发

Thickness control for rolling process by sensitivity based on support vector machine

基于支持向量机灵敏度的轧制过程厚度控制

Research on Temperature and Strain Fields Distribution of Hot Ring Rolling Process

环件热辗扩温度场和应变场分布的研究

The finite element model of wheels sliding on the rails and rolling process are established by large-scale finite element software ANSYS. Establish contact using the contact element method in the wheel-rail contact area.

主要应用大型有限元软件ANSYS分别建立车轮在钢轨上滑动和滚动过程的有限元模型，在轮轨接触区利用接触单元法来建立接触。

Surface Rolling Process of Car's Hub by Diamond Turning Tool

金刚石表面金属化用金刚石车刀抹平加工汽车轮毂

These models were necessary to investigate different thin strip rolling process.

这些模型全面描述了不同状态的板带轧制过程。

Application of computer simulation in cold rolling process of spiral flight

计算机仿真在螺旋叶片冷辗轧过程中的应用

And on basis of this, pointed out metal flowing state and the distribution law of equivalent plastic stress-strain in deformation, described directly out spiral bevel gear forming process and equivalent strain-strain distribution curve, revealed out metal deformation rule during rolling process.

并在此基础上，得出变形中金属的流动状态和等效塑性应力应变分布规律，直观描述出螺旋锥齿轮成形过程及等效应力&应变分布、曲线，获得了轧制成形金属变形规律。

The Study of 72 Mn Bimetal Thin Strip Rolling Process

72Mn双金属薄带轧制工艺的研究

Study of Rolling Process on Non-quenched and Tempered Steel with Tensile Strength of 600-800 MPa

600~800MPa级非调质钢的轧制工艺研究

The 3-dimension finite element models of tool and workpiece in the skew rolling process were built up with ANSYS/ LS-DYNA. Computer simulations on the ladder shaft in skew rolling under different parameters were conducted.

采用ANSYS/LS-DYNA软件，建立了斜轧零件基本变形过程的三维有限元分析模型，对不同工况下的斜轧过程进行了计算机数值模拟分析。

Determination on the place of neutral angle in the rolling process of JD entirety discharge electrode wire

JD整体放电极线轧制中性面位置的确定

Research on Burnish Machine in Compound Material Cold Rolling Process

钢基复合材料生产中打磨机理研究

This paper discusses the effect of rolling process and pass design on product quality for the flat spring steel with single-side and two-slot.

本文阐述了单面双槽弹簧扁钢的轧制工艺及孔型设计对产品质量的影响。

Numerical simulation of new ring rolling process of tubeless steel wheel

无内胎钢制车轮辗环成形新工艺及其数值模拟