rotary speed的例句大全

Function of reducing rotary speed of grader to improve the grade of concentrate

降低分级机转速对提高精矿品位的作用

In this paper, the Mach number control system in NF-6 wind tunnel is introduced, especially in detail for the compressor rotary speed control sub-system, the compressor stator vane control sub-system and the second throat control sub-system. angle.

笔者介绍了NF6风洞马赫数控制系统的组成、特点及运行方式，对转速控制子系统、压缩机静叶角控制子系统、二喉道栅指控制子系统等进行了较为详细的介绍。

So the computer simulation and cutter parameter optimization was conducted, and the optimized data was used in the rotary speed control of cutter bar.

为此对刮刀参数进行了仿真优化并将优化结果用于刮刀转速控制。

The content of terminal carboxyl group can be controlled under the optimal conditions as followed: catalyst concentration 120 μ g/ g, esterification temperature 240 ℃, stirrer rotary speed of final condensation reactor 5 r/ min.

控制PBT端羧基含量的最佳工艺为：催化剂浓度120μg／g，酯化温度240℃，终缩聚釜搅拌器转速5r／min。

The rotary speed has no effect on the working load on cutting teeth.

转速对切削齿上的载荷分布基本无影响。

the actual rotary speed during the stage jump input period could trace the given rotary speed and there was no error during the stabilized period.

实现了阶跃输入时的实际转速对给定转速的跟踪，而且稳态时无偏差。

Low rotary speed during grinding prevents protein denaturing under high temperature caused by grinding.

研磨转速低,能有效避免蛋白质因研磨产生高温而变性.

By the action of high rotary speed, excentric shaft connection intensifies the fatigue failure of tool.

为了达到较好的防斜目的,必须增大钻进时钻头的转速,在高转速的作用下, 偏轴接头加剧了钻具先期疲劳失效.

It is guarantee to get high quality casting that inner casting path and air outlet path are reasonably designed, the rotary speed and clamping force of silicon rubber plats are correctly celebrated.

合理设计铸模的内浇道、出气道，正确选择离心浇注旋转速度和硅橡胶盘片的夹紧力，是获得高质量铸件的保证。

Clutch engagement speed test Calculation of the Interference Fit Joints at High Rotary Speed

离合器接合转速试验高速旋转状态下压配合联接的设计计算

For a rated rotary speed, the torque of the pump increases with the increase of the pressure drop through the pump.

结果表明，泵启动后，双螺杆多相泵转矩随转速的增加而增大；额定转速下，转矩随进、出口压差的增大而增大；

the analysis on experimental result shows that there is an optimum match between weight on bit and rotary speed to prevent hole inclination.

实验结果表明，在防斜问题上也存在最优钻压一转速配合的问题。

The Influence of PCP Test Rotary Speed and Viscosity on the Detection of Its Hydraulic Performance

螺杆泵试验转速和黏度对水力特性检测的影响

The conclusions are as follows: ( 1) under high pressure, the intensity of granite gradually decreases and the percussive rotary drilling speed increases gradually with the increase of temperature;

得出以下结论：①在高围压状态下，随着温度升高，花岗岩的强度逐渐降低，冲击旋转钻进速度随之逐渐增大；

The Speed Stability Criterion of the Rotary Cylinder with Eccentric Load

偏心负载作用下的摆动气缸速度稳定性判据

Simultaneously different rotary angles of a rubber tongue piece also play the speed control function.

同时橡胶舌片旋转不同的角度也起到调速作用。

Under the high-speed rotary condition, the combustion time declined obviously, and the burning rate increased obviously, achieving about 30mm/ s, being 2 times more than that under the static state, and the flame area is obvious larger than that under the static state.

在高速旋转条件下，点火具燃烧时间明显下降，燃烧速度明显增大，达30mm/s左右，是静态下燃速的3倍以上；火焰燃烧面积比静态下明显增大。

The Rule for Determining the Crank Rotary Direction in the Low Speed Crank Slider Mechanism with Six Bars University of Shanghai for Science and Technology

低速曲柄滑块六杆机构曲柄转向的规则

The technics flow of auto-cutter product line of armor plate spring is introduced. The product line is make up of control core by PLC and equipment of determine length by optical rotary encoder and high speed counter.

介绍了钢板掸簧剪切生产线的工艺流程，提出了利用PLC为控制核心，用光电编码器和高速计数器组成测长装置，构成能实现高精度定长剪切功能的自动生产线。

The gearing drive equipment of power head mainly passing low-speed and big torques in working. For bearing to alternate load, fatigue failure of gearing drive equipment becomes the major way of failure for rotary drilling rig power head.

动力头部件中的齿轮传动装置在工作中主要传递低速重载扭矩，而且是交变载荷，齿轮传动装置疲劳破坏是旋挖钻机动力头的主要失效方式之一。