semi-solid的例句大全

containers for pharmaceutical dispensing - specification for glass and plastics containers for solid dosage forms, semi-solids and powders

药剂容器.固体剂型、半固体型和粉末状药剂用玻璃和塑料容器规范

The squeezed-casting formability of AZ 91 D magnesium alloy in semi-solid state was studied.

研究了AZ91D镁合金在不同 半固态 温度下的挤压铸造.

The effects of different agitating temperatures and moltenalloy cooling media on semi-solid microstructure were discussed.

研究了在不用搅拌温度和冷却介质下吹气鼓泡方式 对半 固态组织的影响.

Structural evolutions of ZL 112 Y die cast alloy in procedures of semi-solid die casting were investigated.

研究了ZL112Y压铸铝合金在 半固态 压铸成形过程中的组织演变过程.

The semi-solid feedstock of A 356 aluminum alloy was prepared through a serpentine pouring channel.

采用蛇形管浇注法制备了半固态A356铝合金浆料.

Semi-solid forging is one of new types of materials forging.

半固态 成形是金属材料加工领域中的一种新工艺.

The shaped mechanism of semi-solid ZA 27 alloy is changed along with different shaping temperatures.

随变形温度的不同, 半固态 ZA27合金呈现不同的变形机理.

Semi-solid slurry of Y 112 alloy was cast by near liquidus semi-continuous ( NLSC ).

采用近液相线半连续多模铸造法制备出 Y112 铝合金半固态坯料.

The results indicate that not only segregation phenomenon of primary carbide in the semi-solid structure but also sharp dividing line of the segregation, where the dividing line locates at the distance of about 6 mm from the radial outer face of the annular parts, can be observed.

结果表明，首先在半固态组织中初生碳化物出现偏析现象，且存在明显的偏析分界线，分界线位于距离环形铸件径向外侧面约6mm处。

Semi-solid metal forming is a new process for metal forming.

半固态加工技术是一种新的材料成形技术.

The thixoforming in-semi-solid state based on the semi-solid metal forming was proposed.

在 半固态 金属加工技术的基础上,提出伪半固态触变成形工艺.

A mathematical model of axisymmetric compression of semi-solid alloy slurry was described.

描述了一种轴向挤压的 半固态 合金浆料的数学模型.

A range of processes is now being practiced commercially in semi-solid forming.

一系列工艺过程现已应用在 半固态 成型的商业实践中.

The forming mechanism of semi-solid material of AZ 91 D magnesium alloy was analyzed.

分析讨论了AZ91D镁合金半固态组织的形成机理.

The thixoforming is suitable for the controlling semi-solid forming of and steel with high melting point.

由于触变成形工艺本身的特点,使其更适宜于钢铁等高熔点材料的 半固态 成形控制.

This paper studies mechanical stirring of ADC 12 Semi-solid structure blank.

研究对ADC12铝合金用机械搅拌方法以获得半固态组织坯料.

Preparation of Semi-solid Aluminum Alloy by Sine Function Method

Sin函数冷却法制备半固态铝合金

There has advantage to obtain short and thick primary silicon and improve process efficiency with P modification in semi-solid metal process.

在半固态加工中同时加磷P进行变质细化有利于获得细化的初晶硅，并能减少半固态加工的时间，提高加工效率；

The semi-Solid Forming technique of low melting point alloy has been used in commercial production.

低熔点合金 半固态 成形技术被专家称为21世纪新兴的金属制造关键技术.

So the composite has sensitivity of strain rate during compression in semi-solid interval.

复合材料在 半固态 区间压缩时具有应变速率敏感性.