setting temperature的例句大全

Due to shade deviation and thermal migration of disperse dye, so dyes selection and temperature control of post setting should be pay attention to.

由于分散染料在织物上有色光偏移和热迁移现象，应注意染料的选择和控制后定形温度。

Methods: The setting expansion ratio of refractory die material for slip casting core of sintered titanium powder at room temperature was performed, as well as thermal expansion ratio from room temperature to 800 ℃.

方法：采用自制的钛合金粉浆涂塑底层冠用耐火代型材料（基础型），分别测定常温下的凝固膨胀率和室温至800℃的热膨胀率。

Through contrast tests, the best deposition process is obtained by setting deposition time as invariant, the reaction gas flow rate and deposition temperature as variables.

通过对比试验，以沉积时间作为不变因素，反应气体流量和沉积温度作为变量进行工艺研究，分析了工艺参数对成膜质量的影响。

Based on a superheated steam temperature control system of a boiler ( 1650 t/ h) in a power plant, this paper presents a robust double-loop cascade control algorithm with both dimension-decreasing state observer and PI controller. The corresponding setting rule of parameters is also given.

本文以某电厂1650吨／时大型锅炉过热器出口蒸汽温度控制系统为研究对象，提出了一种带有降维状态观测器和PI的鲁棒双环串级控制方法，并给出了相应的参数整定算法。

By setting the sliding floor a breathing system was built up and the temperature stress reduced distinctly.

通过设置滑动层，使结构成为一种可呼吸体系，从而有效地降低温度应力。

Using finite element software to analyzes temperature effect of overlong concrete structure on the condition of four different restrains, and the imitating results proof that the temperature stress was reduced efficaciously by setting the sliding floor, therefore alleviate the crack of the concrete structure.

对超长混凝土结构在四种不同约束状态下的温度效应进行了模拟分析，论证了在超长混凝土结构底板采用滑动摩擦处理能够有效的降低底板温度应力，缓解混凝土开裂。

The breaking strength and resilient-elasticity recovery of PTT fabric can be increased under suitable temperature and drawing ratio during heat setting, but its dilatability took worse.

选择适当的温度和拉伸比进行热定形，可提高PTT织物的断裂强力和弹性回复率，但其延伸性变差。

Development of Expediting Setting Epoxy Resin Adhesives with Low Cost in Room Temperature

低成本室温快速固化环氧树脂胶粘剂的研制

The static plasticity coefficient of retarding mortar of three different proportions ( A, B, C) are tested in this paper, and the effect of temperature, age, addition of compound retardant and different cement type on retarding setting time of retarding mortar.

试验测定了A，B，C三种不同配比的缓凝砂浆静态塑性指数，分析了温度、龄期、复合缓凝剂的掺量及不同水泥品种对缓凝砂浆的缓凝时间的影响。

The study results of this paper can be used to guide the utilization of the late poured band in large scale plate-type concrete structures, and provide useful methods in analysis of temperature, stress and the setting separation distance of the late poured band.

本文的研究成果可以用来指导后浇带在大尺度板式钢筋混凝土结构中的应用，也为分析后浇带温度、应力和设置间距提供了可借鉴的方法。

Intelligent Digital temperature control, key-in setting, automatic constant temperature control, friendly operation.

数字智能温控，按键设定，自动恒温，操作方便。

The experimental result indicates: temperature controlling stability of laser constant temperature controlling system may achieve 5 m ℃, and temperature setting is extremely flexible.

实验结果表明：该激光器恒温控制系统的温度控制稳定度可达5m℃，并且温度设定非常灵活。

Study on Effect of Environment Temperature and Setting Position in the Horizontal Direction on the Alarm Response Time of Smoke Detectors

环境温度及水平安装位置对感烟型火灾探测器响应性能影响的研究

The article uses FDS to study the effect of environment temperature and setting position on the alarm time of smoke detectors.

用FDS软件研究了环境温度和水平安装位置对感烟型火灾探测器报警时间的影响。

By doing so, the DET keeps the system pressure below the relief setting of the Temperature and Pressure relief valve.

通过这种功能，DET系列将系统压力保持在温度压力安全阀的排放设置下。

Relationship between Rice Grain Quality and Temperature during Seed Setting Period

结实期温度与稻米品质的关系

AIRPORT ANALYSIS, A comprehensive set of takeoff weight limitations for a given airport runway, generally presented as a function of airport temperature, wind, and aircraft flap setting.

机场分析，一套针对给定的机场跑道的详细重量限制资料。通常与机场温度、风、和飞机襟翼位置成函数关系。

intermediate temperature setting solvent-free epoxy resin structural adhesive with high tenacity and high peeling strength modified by pu

中温固化高强度高剥离无溶剂聚氨酯改性环氧树脂结构胶粘剂

the temperature stress in the back pouring band of the platform concrete is monitored. the result shows that setting the back pouring band reasonably can reduce the effect on structure due to temperature stress.

对平台的后浇带温度应力进行监测，监测结果表明：合理地设置后浇带能有效地减少温度应力对结构影响。

With digital temperature setting , time setting and airflow control , the performance is more efficiently and precisely.

配合数控温度,时间设定, 蓝光气流显示,可准确及有效率对芯片进行返修.