shaft drive的例句大全

Put on chain between crankshaft drive sprocket and intermediate shaft drive sprocket.

安装曲轴传动链轮和中间轴传动链轮之间的链条。

The counter drive shaft drives a couple of bevel gears to achieve coal put out.

副传动轴带动一对锥齿轮副实现输出煤.

Overhead cam shaft Programming of Inner-milling of Crankshaft Drive Spindle with Parameters R

上凸轮轴上部凸轮轴基于R参数的曲轴主轴颈内铣加工循环编程

Dynamic analysis of locomotive cardan shaft drive systems

机车万向轮驱动系统动力学分析

Drive shaft, Tie rod end assembly, Ball joint, Control arm assembly.

悬挂球头、拉杆球头、横拉杆、拉杆总成、控制臂总成等。

Tighten lock nut for the drive shaft to the specified tightening torque.

将驱动轴的锁紧螺母拧紧至规定的拧紧力矩。

Development of Vehicle Drive Shaft Quasi-Static Torque Testing Bed

汽车传动轴似静扭试验台

Drive idler gear reverse idler gear shaft bearing

空转传动齿轮，怠速齿轮

The design and development of low temperature test box is for testing the reliability of rubber boot on automobile drive shaft.

汽车传动轴橡胶（塑）护套低温试验箱是为了测试橡胶护套在多种低温情况下的安全可靠性而研制的。

There must be one or more universal joints to permit variations in the angle of drive. There must also be a slip joint that permits the effective length of the propeller shaft to change.

可轴向移动的球笼式万向节一个或几个万向节来适应传动角度的变化；一套伸缩花键，能够改变传动轴的现有长度。

Make sure that the ball joint boots and drive shaft boots are not damaged during removal and installation.

确保在拆卸与安装过程中未损坏球头防尘套和驱动轴防尘套。

The upper part of the drive shaft is provided with a big belt wheel and the bearing seat, and one end of the drive shaft is provided with an eccentric wheel.

在传动轴上装有大皮带轮和轴承座，并在传动轴的一端装有偏心轮；

Rear axle differential side gear differential spur drive pinion cross shaft

差速器传动（正）齿轮后桥差速器半轴齿轮

Pull the long drive shaft out of the gear mount and check for damage.

将长驱动轴从齿轮支座中拔出并检查是否损坏。

The Application of Hydraulic Control System in Assembly of Drive Shaft

液压控制系统在传动轴装配中的应用

Next it designed the structure and dimension parameters of key components such as spiral shaft, drive motor, feed bin and discharging device according to traditional design method of spiral conveyor and specific production requirements.

之后参考螺旋输送器传统的结构设计方法，结合该饲喂装置的具体生产使用要求对螺旋轴、驱动电机、料仓、出料斗等关键零件的结构及尺寸参数进行设计。

Drive components of the drive shaft and the driven shaft are moved away, so that the cost is reduced.

取消了主动轴到从动轴的传动部件，降低了成本。

The Design on Painting Production Line for Car's Drive Shaft

汽车传动轴涂装生产线设计

Discussion about Improving the Heat Treatment Quality of Compressor Drive Shaft

关于提高压缩机驱动轴产品热处理质量的探讨

The Optimization of Car Drive Shaft Assembly Based on Finite Element Analysis

基于有限元分析的轿车半轴总成优化设计研究